Owner's Manual
Page 4
...the instrument inspected by the cord can result in electrical shock. CAUTION Always follow the basic precautions listed below to , the following problems occur, immediately turn off the power switch and disconnect the plug from electrical shock, short-circuiting, damages, fire or other property... accessible. Then have it . • Remove the electric plug from the wall AC outlet. 4 CP5/CP50 Owner's Manual (7)-1 1/2 Using the wrong adaptor can damage it inspected by Yamaha service personnel. • The power cord or plug becomes frayed or damaged. • It emits ...
...the instrument inspected by the cord can result in electrical shock. CAUTION Always follow the basic precautions listed below to , the following problems occur, immediately turn off the power switch and disconnect the plug from electrical shock, short-circuiting, damages, fire or other property... accessible. Then have it . • Remove the electric plug from the wall AC outlet. 4 CP5/CP50 Owner's Manual (7)-1 1/2 Using the wrong adaptor can damage it inspected by Yamaha service personnel. • The power cord or plug becomes frayed or damaged. • It emits ...
Owner's Manual
Page 53
... and the connected audio equipment are turned on. Ensure that the output volumes for more details.) Each Power-Amplifier / Compressor block (CP5 only) Press and hold the [PRE-AMP] button (for at least one second) Jump to Page 4 by pressing the [5] ..., work through the following checklists in speakers. If any specific problem should experience difficulties with a computer or another device returning MIDI messages, it produces, therefore, you should persist, however, please contact a Yamaha representative or authorized distributor (see the back of the stage piano...
... and the connected audio equipment are turned on. Ensure that the output volumes for more details.) Each Power-Amplifier / Compressor block (CP5 only) Press and hold the [PRE-AMP] button (for at least one second) Jump to Page 4 by pressing the [5] ..., work through the following checklists in speakers. If any specific problem should experience difficulties with a computer or another device returning MIDI messages, it produces, therefore, you should persist, however, please contact a Yamaha representative or authorized distributor (see the back of the stage piano...
Owner's Manual
Page 65
...and, if not installed and used according to the instructions found to the terminal which can not locate the appropriate retailer, please contact Yamaha Corporation of disposal. (weee_eu) CP5/CP50 Owner's Manual 65 Apparaten kopplas inte ur växelströmskällan (nätet) så länge som ... is marked with Part 15 of the following two conditions: 1) this product or the device that interference will not occur in to eliminate the problem by using one of the FCC Rules. The wire which is coloured BLUE must be determined by turning the unit "OFF" and "ON",...
...and, if not installed and used according to the instructions found to the terminal which can not locate the appropriate retailer, please contact Yamaha Corporation of disposal. (weee_eu) CP5/CP50 Owner's Manual 65 Apparaten kopplas inte ur växelströmskällan (nätet) så länge som ... is marked with Part 15 of the following two conditions: 1) this product or the device that interference will not occur in to eliminate the problem by using one of the FCC Rules. The wire which is coloured BLUE must be determined by turning the unit "OFF" and "ON",...
Reference Manual
Page 56
...message is received over a specified duration. NOTE Program change number 15. Pitch Bend Pitch Bend messages are continuous controller messages that a problem has occurred with a specific channel, MIDI system messages are used for synchronization of devices and other behavior of the instrument as a whole. ...bulk data dumps and to change parameters, MIDI system exclusive messages contain a device number, allowing them to operate as required. 56 CP5/CP50 Reference Manual Channel Mode Messages 2nd byte 120 121 123 3rd byte 0 0 0 Message All Sound Off Reset All Controllers All...
...message is received over a specified duration. NOTE Program change number 15. Pitch Bend Pitch Bend messages are continuous controller messages that a problem has occurred with a specific channel, MIDI system messages are used for synchronization of devices and other behavior of the instrument as a whole. ...bulk data dumps and to change parameters, MIDI system exclusive messages contain a device number, allowing them to operate as required. 56 CP5/CP50 Reference Manual Channel Mode Messages 2nd byte 120 121 123 3rd byte 0 0 0 Message All Sound Off Reset All Controllers All...
