Yamaha ACD1 Support and Manuals
Get Help and Manuals for this Yamaha item
Popular Yamaha ACD1 Manual Pages
Owner's Manual - Page 3
... only high quality shielded cables. See user manual instructions if interference to radio reception is subject to the following code:
GREEN-AND-YELLOW : EARTH
BLUE
: NEUTRAL
BROWN
: LIVE
As the colours of the wires in the mains lead of Equipment : Amplifier Control Device
Model Name : ACD1
This device complies with other electronic devices...
Owner's Manual - Page 4
...switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel.
• If this manual... connected cables. • When setting up the device, make sure to... The device contains no user-serviceable parts. If you intend to ,... in an unstable position where it .
4 ACD1 Owner's Manual
(5)-6 1/2 These precautions include, but are not...
Owner's Manual - Page 5
... Current: 45A Conforms to Environments: E1, E2 E3 and E4
● SPECIAL NOTICES The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may be held responsible for example. Then have qualified Yamaha service personnel replace the backup battery.
Consult qualifi ed Yamaha service personnel about replacing defective components.
Owner's Manual - Page 7
... manuals ACD1 Reference Manual Amp Editor Installation Guide
Amp Editor Owner's Manual
Provides a detailed explanation of the ACD1
The ACD1 is able to monitor and control up Amp Editor and the ACD1, and how to the ACD1 ...series units can be installed in a single network, a larger number of the website. Explains how to set up to 40 amplifiers
A single ACD1 unit is an ampli&#...
Owner's Manual - Page 8
....yamahaproaudio.com/downloads/
8 ACD1 Owner's Manual Terms
This section explains terminology specific to the ACD1.
■ Scene
Settings such as power-on/standby or mute for each amplifier are called a "scene." Scene links can update the firmware via Amp Editor. For the update procedure, refer to the following Yamaha website.
http://www.yamahaproaudio...
Owner's Manual - Page 11
... whether the connected cable is of 8 amps
TXn series
NOTE
Connections between the computer or network switch and the ACD1 can use either a straight or crossover cable. ACD1 Owner's Manual 11
However, due to variations in computers, network switches, and cable quality, proper operation at the maximum length cannot be guaranteed in some cases.
•...
Owner's Manual - Page 14
... Control
3. Network Setup
Clock Setup GPI Calibration IP Address Mode
IP Address MAC Address IP Ctrl Port #
Operation performed Recalls a scene on the specified amplifier. Displays the name of the ACD1's internal clock. Selects whether the ACD1's LCD backlight will be set automatically from Amp Editor (DHCP) or set manually (Manual). Specifies...
Owner's Manual - Page 15
... to "Auto OFF."
While holding down . Never power-off the ACD1.
2. Troubleshooting
Symptom All scene data saved in the ACD1 reference manual.
"LCD Backlight" is set to "Disable." CAUTION
Use caution when performing the following steps.
1. CAUTION
ACD1 Owner's Manual 15 The LCD is locked.
Check [5.Utility] → [Battery] for each alert message and the appropriate...
Reference Manual - Page 5
...YAMAHA ACD1 001:FOH #1
Device ID
Device Label ....... w [BACK] button Use this to move to internal memory at regular intervals, so you sure?".
The panel lock will be temporarily defeated until the power to the ACD1... unit will appear. ACD1 Reference Manual 5
If characters not supported by Amp Editor....HOME screen is displayed, the Device ID setting screen will start up the unit so ...
Reference Manual - Page 6
...switch performance, however, proper operation at the maximum length cannot be monitored/controlled from the ACD1. Due to 5V. The IN terminals detect voltage changes from external equipment. If the AC outlet used is earthed (grounded), this connector must be set to non-overlapping numbers in countries where FCC regulations apply.) Since the ACD1 supports...
6 ACD1 Reference Manual For ...
Reference Manual - Page 7
...ACD1's firmware version. Restricts panel operations of the ACD1's internal backup battery. Sets the date and time of the specified amplifier. Displays the ACD1's MAC address. Device Setup (page 12)
5. Displays the name of the corresponding ACD1... ACD1's internal clock. Selects whether the ACD1's IP address will not be monitored/controlled.
ACD1 Reference Manual ...
Reference Manual - Page 10
...protected Selects the scene number to be ignored if a different model of 12 characters. NOTE
• If the screen indicates "(scene...returning the amplifiers to their default settings.
• If characters not supported by the ACD1 are a maximum of amplifier ... ALL
01-49 See character list at the end of this manual
Explanation Selects the ID of all amplifiers.
Scene")
...
Reference Manual - Page 13
... internal backup battery. V1.10
ACD1 Reference Manual 13
Identify OåN
Parameter Identify
Range ON/OFF
Explanation
If this case, immediately save the data to update the ACD1's firmware. For details, refer to have the backup battery replaced.
■ Version indication ("5.
Utility" ➝ "Firmware Ver.")
Displays the ACD1's firmware version. Panel operations...
Reference Manual - Page 15
...Clock setting ("5. Sets the month. Sets the hour.
Panel operations
■ Enabling scene recall operations via EMG commands ("5.
ACD1 Reference Manual 15 ...The unit will not be switched to the specified state. Sets the year.
Recalls the ...Setup area may indicate "Some ON." The following three types of the ACD1's internal clock. Utility" ➝ "EMG Scene Setup...
Reference Manual - Page 23
...RJ-45
Euroblock (3.5 mm pitch)
RJ-45
*1 Supported models XP7000, XP5000, XP3500, XP2500, XP1000, XM4180, XM4080, XH200 Guaranteed cable length: 50m
*2 Supported models T5n, T4n, T3n, PC9501N, PC6501N, PC4801N, ...REMOTE CONTROL
3
MONITOR
4
REMOTE CONTROL
5
6
7
8
MONITOR
9
10
11
12
13
14
15
STANDBY MODEL ID MUTE CH D MUTE CH C MUTE CH B MUTE CH A PROTECT STATUS CH D PROTECT STATUS CH...
Yamaha ACD1 Reviews
We have not received any reviews for Yamaha yet.