Xerox N2125N - DocuPrint B/W Laser Printer Support and Manuals
Get Help and Manuals for this Xerox item
View All Support Options Below
Free Xerox N2125N manuals!
Problems with Xerox N2125N?
Ask a Question
Free Xerox N2125N manuals!
Problems with Xerox N2125N?
Ask a Question
Most Recent Xerox N2125N Questions
Popular Xerox N2125N Manual Pages
User Guide - Page 49
...described in the section "Generating a Printer Report" (page 3-60). Configuring the Printer Drivers
When you initially use any of your printer drivers, make sure to properly configure them for UNIX Systems UNIX TTY Services
Installing the Printer Drivers
Inside the cover of the printer CD case is a booklet with instructions on how to your printer will support, you are displayed under the...
User Guide - Page 174
... cord receptacle Location • 1-7
Power switch Location • 1-7
Print speed • 1-6 Printer cleaning • 4-2 Printer components • 1-7 ¨ 1-9 Printer drivers
See Drivers Printer Management Software CD • 1-10, 1-12 Printer reports
Printing • 3-60 Types • 3-60 Problems See Troubleshooting Product CD • 1-10, 1-12 Proof printing PCL jobs • 3-10...
Service Manual - Page 4
... table, error code tables and the Repair Analysis Procedures (RAPs).
Section 5 - This information is not specific to assist in this section of the manual is provided for removal, replacement, and adjustment of the service manual should always be used to isolate and identify problems to start the service call.
Repair / Adjustment
This section contains the instructions for...
Service Manual - Page 13
... Analysis Procedures (RAPs) Section 3 - Wiring All service calls start with Initial Actions and all service calls end with Final Actions. Figure 1 Call Flow Diagram
Service Call Procedures
1.2
02/2000 1-4
Initial Issue DocuPrint N2125 The functions in Call Flow correspond to service manual sections as follows: Section 1 - Repair / Adjustment (REPs) Section 5 - 1.2 Call Flow
The call flow...
Service Manual - Page 20
... the problem has been corrected. Use the Error Code Tables when messages or error codes are accessed from Section 1, system checks or additional checks.
RAPs will normally isolate a problem to frame ground, therefore all circuit troubleshooting can be performed using the metal frame (chassis) as the grounding point. Measurements
Power and signal grounds are connected to a specific component...
Service Manual - Page 36
... at the Exit Sensor.
YN
Repair actuator or replace the Fuser Assembly (REP 6.2). Scroll to RAP 48. YN
Replace the Exit Rollers or Gears as necessary. YN
Clean or replace the Fuser Assembly (REP 6.2), as necessary (PL 7.1). The lead edge of obstructions.
RAP 11 Paper Jam / Exit (E4)
There is within specification.
When the error code is displayed, there is...
Service Manual - Page 43
... print quality meets specifications. YN
Go to Sensor Input and press Enter [4]. The voltage is 0.0VDC with the print cartridge installed and 3.3VDC with paper that is moved. Replace the Toner Sensor (REP 5.2).
Procedure
The problem appears when using Tray 1, 2, or 3. Enter the User Menus, select Tray Menu, then select MBF Size. YN
Set MBF size to...
Service Manual - Page 58
... power on .
YN
Switch the printer power off .
YN
Attribute the problem to a poor connection between the DIMM and the System
Controller PWB.
The error code reappears. The error code reappears.
Install the removed DIMM in Slot 2 (bottom DIMM slot). Switch
the printer power on . Switch the printer power on . Switch the printer power on . Replace the System Controller PWB (REP...
Service Manual - Page 87
... Heat Roll and the Pressure Roll are clean and unobstructed. Load fresh, dry paper. Install a new Print Cartridge. Open the Rear Cover. Open fuser jam access cover. Rotate the fuser idler gear manually and inspect the Pressure Roll. If the problems persist, replace the System Controller PWB (REP 9.2).
Scroll to be hot. Remove and reseat the System...
Service Manual - Page 88
... the fuser idler gear manually and inspect the Heat Roll.
Run a test print. YN
Problem solved. YN
Problem solved.
paper
A
02/2000 3-15
Image Quality Repair Analysis Procedures
IQ RAP 4 , IQ RAP 5
manuals4you.com Vertical band deletions are free of the Print Cartridge. • Check that the paper supply is solved: HVPS PWB (REP 9.6), Print Cartridge Side Guide...
Service Manual - Page 89
... as staples, paper clips and paper scraps. • Check installation of the Print Cartridge. • Check that the paper supply is dry and fresh. • Inspect the printer paper path for contamination and wear. The problem is free of contamination and wear. Rotate the fuser idler gear manually and inspect the Pressure Roll. WARNING
If the...
Service Manual - Page 91
... replace the Print Cartridge Side Guide (REP 7.5).
Image Quality Repair Analysis Procedures
IQ RAP 7 , IQ RAP 8
Figure 1 Horizontal Streaks
Initial Actions
• Check that the paper supply is dry and fresh.
• Inspect the printer paper path for contamination and wear.
A YN Remove any obstructions from the laser beam path. Rotate the fuser idler gear manually and...
Service Manual - Page 92
... appear. Install a new Print Cartridge. YN
Replace the BTR Assembly (REP 7.1). Generate a Test Print and switch OFF the printer power halfway through print cycle. The toner image on the Drum was not removed during the cleaning process, has been developed on the Drum just before the transfer area (BTR).
Open the fuser jam access cover.
Problem solved...
Service Manual - Page 256
...and displays the problem found on the LCD. 4. Press key 1 or 5 to scroll through Print Menu containing: Print Pattern, Input Tray, Output Tray, and Duplex
3 or 7
Scrolls all supported paper sizes) • Output Tray selection • Duplex selection • Display error message/code when failure occurs (Table 2). It will be installed properly Replace EP Cartridge Empty face down...
Service Manual - Page 257
... request password. Condition / Message Face up tray open Tray 1 out install tray Tray 2 out install tray Tray 3 out install tray (Main Drive) Motor Fail ROS Fail Fuser Fail Fan Fail (IOT) NVM Fail Duplex Unit Fail Envelope Feeder unit fail OCT Unit fail Optional Feeder Unit fail Set pause command Fuser Warning
Table 2 IOT Fault Table UI Error Code E5...
Xerox N2125N Reviews
We have not received any reviews for Xerox yet.