Whirlpool WRT108FFD Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WRT108FFD manuals!
Problems with Whirlpool WRT108FFD?
Ask a Question
Free Whirlpool WRT108FFD manuals!
Problems with Whirlpool WRT108FFD?
Ask a Question
Popular Whirlpool WRT108FFD Manual Pages
Owners Manual - Page 2
...problems of the past. WARNING
Suffocation Hazard Remove doors or lid from your appliance. If you throw away your appliance, follow the safety alert symbol and either the word "DANGER" or "WARNING."
All safety messages will tell you what can be used in this manual...instruction concerning use of the appliance by the manufacturer, its service... Do not use replacement parts that they will ...
Owners Manual - Page 6
... be used on your local plumbing codes. Install copper or PEX tubing only in the Quick Start Guide. NOTE: Before performing any tools listed.
Do not use a cord that a separate circuit serving only your water pressure, see "Troubleshooting" online or call a licensed, qualified plumber.
6 Gather the required tools and parts before you move your refrigerator...
Owners Manual - Page 10
... . First, drive the bottom two screws into handle.
8. Set aside door until hinges and refrigerator compartment door are not reversing the doors, see the Brand Badge Placement template (the last page of the freezer door. Refrigerator Handle
D. Standard Door Models Graphics follow these instructions.
3. Remove door hinge hole plug from the door.
�...
Owners Manual - Page 11
...plug and discard. Replace on both the ...Models Graphics follow these instructions. Move to opposite side hinge holes as shown. Remove cabinet hinge hole plugs from refrigerator door. Move to opposite side hinge hole as shown below . Replace screw cover. A. 5/16" Hex-head hinge screws B. Cabinet Hinge Hole Plugs
11 Set aside refrigerator door until bottom hinge is installed...
Owners Manual - Page 13
....
4. Check all screws. Remove the cover from the base grille. Replace the parts for the doors while the hinges are working.
2. Replace the refrigerator door.
Failure to the hinge. Contour Door Models Only: � Remove the screw attaching the hinge pin to follow these instructions can result in the opposite direction. � Place the plastic...
Owners Manual - Page 15
...above the desired support
and pushing ...Replace the rails by pulling straight up on each end of packaging or wrap used (should be installed in slightly on the inside a sealed package are normal. The freezer door must close tightly. Style 1 -Door Rails
Half-Width Shelf (on some models...Guide
Storage times will freeze within 24 hours (no more unfrozen food into the
tracks on some models...
Owners Manual - Page 17
... off bruised and discolored areas. After replacing the ice storage bin, turn on a refrigerator shelf. � Vegetables with skins: Place in plastic bag or plastic container and store in the crisper for use . Crisper Humidity Control (On Some Models) You can be easily installed by the user, following instructions given with the kit. Low...
Installation Instructions - Page 4
... 14. Read through the entire step so that you understand it .
2. Pliers 5. 1⁄4" nut driver 6. Before You Begin
Tools
Gather required tools and parts before you are contained in each set of steps shown, refer to perform. Follow the instructions carefully. Some illustrations also contain "DETAILS." DETAILS are to the diagram immediately beside or...
Installation Instructions - Page 5
...11
12
14
13
* For installation in Side-By-Side Models only.
15
16
17
18
** For installation in the kit against the following list to order a replacement part for all of the components in... tubing from the styrofoam packing insert, do not remove the tubing from the shipping carton and set them .
Do not discard any of the components. Components
Remove the contents from the valve...
Installation Instructions - Page 6
...the areas to your "Use and Care Guide" for all of the freezer section. On top-mount models without a full-width freezer shelf, remove...wall
left side of the door. Installing the Ice Maker
Making preparations
Refer to support the ice bucket. Gently pull ...Shock Hazard Disconnect power before installing ice maker. Failure to work area for the procedure). Set these areas
Rear wall
Rear ...
Installation Instructions - Page 11
... access cover, then remove the cover and set it aside. Center the clips between the fill tube and the top of the tubing clips.
Installing the tubing clips
Refer to page 12.
Press...
1. NOTE: If you have a bottom freezer, proceed to the side diagram for bottom freezer models
Remove 7 hexhead screws from rear access cover
Right channel
DETAIL B
Tubing clip
Top and SXS freezers...
Installation Instructions - Page 18
Remove plastic cap from the wall for leaks. Attach the
copper tubing to your model. 1. Create a service loop with a "P" clamp, using a compression nut and sleeve as shown. Copper tubing
C. Compression sleeve
3. 8. Connect to Refrigerator Follow the connection instructions specific to the valve inlet using the original screw in the panel slot above the valve.
Tighten...
Installation Instructions - Page 21
... This completes the installation of ice and discard them. Installing the ice bucket...mount models without a full-width freezer shelf, you have any problems,... refer to place the ice bucket on the edge of the freezer shelf.
After that it
Turning the ice maker on page 22. Next, place the ice bucket on top of the freezer floor.
The ice bucket will need to "Troubleshooting...
Installation Instructions - Page 22
... (contact your water utility company and have the water pressure checked.
2. Troubleshooting chart
The following sounds is equipped with your Ice Maker's ability to fill the ice bucket. PROBLEM One or more ice, adjust the freezer control for a colder setting. Be sure that acts like a pressure regulator to provide this service). Water is old.
Installation Instructions - Page 23
... ARM. Specifications
MOLD HEATER - 185 WATTS, 72 OHMS THERMOSTAT - ADDITIONAL ROTATION COULD DAMAGE MODULE. INDEX KNOB AND REINSTALL IN SAME POSITION FOR WATER FILL. MODULE, MOTOR, AND SUPPORT ASSEMBLY INSERT PHILLIPS DRIVER IN ACCESS PORTS IN MODULE.
PULL OUT RETAINING CLIPS WITH BIMETAL.
ONE REVOLUTION (EJECTS AND WATER FILL) FOR 120 VOLT MODEL
Water...
Whirlpool WRT108FFD Reviews
We have not received any reviews for Whirlpool yet.