Installation Instructions
Page 1
SP 1 ELECTRIC DRYER INSTALLATION INSTRUCTIONS Para una version de estas instrucciones en español, visite www.Whirlpool.com Table of Contents DRYER SAFETY 2 Installation Requirements 3 Tools and Parts 3 Location Requirements 4 Electrical Requirements 4 INSTALL LEVELING LEGS 6 ELECTRICAL INSTALLATION 7 Power Supply Cord Connection 8 Direct Wire Connection 10 VENTING 13 Venting Requirements 13 Plan Vent...
SP 1 ELECTRIC DRYER INSTALLATION INSTRUCTIONS Para una version de estas instrucciones en español, visite www.Whirlpool.com Table of Contents DRYER SAFETY 2 Installation Requirements 3 Tools and Parts 3 Location Requirements 4 Electrical Requirements 4 INSTALL LEVELING LEGS 6 ELECTRICAL INSTALLATION 7 Power Supply Cord Connection 8 Direct Wire Connection 10 VENTING 13 Venting Requirements 13 Plan Vent...
Installation Instructions
Page 3
... with upturned ends. ■■A UL listed strain relief. 1/4" and 5/16" nut driver (recommended) Adjustable wrench that all parts are included. Utility knife Tape measure Leveling legs (4) "Y" connector Level Pliers Caulking gun and compound (for installing new exhaust vent)...■■Vent clamps ■■Vent elbows and ductwork Additional parts may be at least 4 ft. (1.22 m) long. INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before purchasing parts. Tools needed: Flat-blade screwdriver #2 Phillips screwdriver Wire stripper (direct...
... with upturned ends. ■■A UL listed strain relief. 1/4" and 5/16" nut driver (recommended) Adjustable wrench that all parts are included. Utility knife Tape measure Leveling legs (4) "Y" connector Level Pliers Caulking gun and compound (for installing new exhaust vent)...■■Vent clamps ■■Vent elbows and ductwork Additional parts may be at least 4 ft. (1.22 m) long. INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before purchasing parts. Tools needed: Flat-blade screwdriver #2 Phillips screwdriver Wire stripper (direct...
Installation Instructions
Page 4
... valves, and water pressure of 200 lbs. (90.7 kg). If a closet door or louvered door is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. Left or right side exhaust 3/4"* (18 mm) 61/2" (165 mm) Power supply cord/cable Vent Water inlet 297/8"* (759 mm) 31/2"* (89 mm...
... valves, and water pressure of 200 lbs. (90.7 kg). If a closet door or louvered door is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. Left or right side exhaust 3/4"* (18 mm) 61/2" (165 mm) Power supply cord/cable Vent Water inlet 297/8"* (759 mm) 31/2"* (89 mm...
Installation Instructions
Page 5
... is installed in conformance with equivalent ventilation openings are required. The neutral ground conductor is suitable for Mobile home construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH. Recommended installation clearances (dryer only): 18" min. (457 mm) 3" (76 mm) 48 in remodeling after 1996, (2) mobile ...9632;Do not use with upturned ends. ■■A UL listed strain relief. 5 Connect to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for mobile home installations.
... is installed in conformance with equivalent ventilation openings are required. The neutral ground conductor is suitable for Mobile home construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH. Recommended installation clearances (dryer only): 18" min. (457 mm) 3" (76 mm) 48 in remodeling after 1996, (2) mobile ...9632;Do not use with upturned ends. ■■A UL listed strain relief. 5 Connect to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for mobile home installations.
Installation Instructions
Page 18
...q If you have all of the water system, which will go back through the water system in the dryer. Complete Installation CHECKLIST q Check that all parts are set in a running or "On" position. • Start button has been pushed firmly. • Dryer is plugged into a grounded outlet. Do ... door is closed. If there is level. The odor will reduce product performance. Over time, the buildup of lime scale may clog different parts of your Use and Care Guide. This dryer automatically runs an installation diagnostic routine at the start of /recycle all packaging materials.
...q If you have all of the water system, which will go back through the water system in the dryer. Complete Installation CHECKLIST q Check that all parts are set in a running or "On" position. • Start button has been pushed firmly. • Dryer is plugged into a grounded outlet. Do ... door is closed. If there is level. The odor will reduce product performance. Over time, the buildup of lime scale may clog different parts of your Use and Care Guide. This dryer automatically runs an installation diagnostic routine at the start of /recycle all packaging materials.
Warranty
Page 1
...REPAIR AS PROVIDED HEREIN. You must be found by checking the "Assistance or Service" section or by calling Whirlpool. You will pay for Factory Speci ed Parts and repair labor to correct house wiring or plumbing. 3. The removal and reinstallation of purchase or installation ...be provided by an authorized Whirlpool servicer is required to be easily determined. Dealer name Address Phone number Model number Serial number Purchase date 16 If you are excluded from the date of original purchase date is not available. 9. Replacement parts or repair labor on ...
...REPAIR AS PROVIDED HEREIN. You must be found by checking the "Assistance or Service" section or by calling Whirlpool. You will pay for Factory Speci ed Parts and repair labor to correct house wiring or plumbing. 3. The removal and reinstallation of purchase or installation ...be provided by an authorized Whirlpool servicer is required to be easily determined. Dealer name Address Phone number Model number Serial number Purchase date 16 If you are excluded from the date of original purchase date is not available. 9. Replacement parts or repair labor on ...