Whirlpool WED4810BQ Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WED4810BQ manuals!
Problems with Whirlpool WED4810BQ?
Ask a Question
Free Whirlpool WED4810BQ manuals!
Problems with Whirlpool WED4810BQ?
Ask a Question
Popular Whirlpool WED4810BQ Manual Pages
Use & Care Guide - Page 4
n Replace plastic or foil vent material with heat, dryers require good air flow to efficiently dry laundry. The venting system attached to follow the "Installation Instructions" supplied with your dryer for the occasional damp load that needs a little more than four 90° elbows in good air flow. Service calls caused by improper venting are sensed in...
Use & Care Guide - Page 5
... models with a selectable temperature knob, you are unsure of the cycle reduces wrinkling.
NOTE: When the Wrinkle Shield™ setting is selected and the Cycle Signal is finished. Gives the best drying in the load or air temperature and shuts off at the end of the temperature to start the dryer.
See "Cycle Guide...
Use & Care Guide - Page 6
... drier than the higher setting. TIMED DRY CYCLES
Not all models.
NOTE: If you dry a similar load. CYCLE GUIDE - Items to a damp level or for optimal energy savings. Dries items to dry:
Cycle:
Temperature:
Available Options:
Cycle Details:
Jeans, heavy work clothes.
If you dry a similar load.
Will run the dryer for the specified...
Use & Care Guide - Page 8
... to remove a load from the dryer as soon as it cannot be changed without stopping the cycle. Promptly removing clothes at which the dryer will sound every 5 minutes until ... some models) n Get 90 minutes of the cycle reduces wrinkling. Choose ENERGY PREFERRED for more load moisture. See the Cycle Guide for optimal energy savings. ENERGY PREFERRED is finished. Set cycle settings and ...
Use & Care Guide - Page 10
... driver, remove the screw located in death or electrical shock. Unplug or disconnect power to dryer pipe. 4. Cap the open fuel supply line. 5. Replace the bulb with the screw.
4. Remove the cover. Replace all parts and panels before servicing.
Disconnect gas supply line pipe and remove fittings
attached to dryer. 2. Reinstalling the Dryer
Follow the "Installation Instructions...
Use & Care Guide - Page 11
... system of lint or replace exhaust vent with lint. The gas valve clicking is not crushed or kinked. Clothing knotted or balled up , the load will bounce, causing the dryer to check air movement.
See "Installation Instructions".
Has the Fluff Air cycle or No Heat temperature setting been selected.
See "Cycle Guide." Exhaust vent or outside...
Use & Care Guide - Page 12
... before the end of the cycle. If so, ventilate the area. TROUBLESHOOTING cont. Lint on high.
Use Timed Dry for assistance and to avoid wrinkling.
This reduces overdrying.
12
Add dryer fabric softener sheets at www.whirlpool.com/product_help In Canada www.whirlpool.ca for very small loads. All cycles are caused by dyes...
Use & Care Guide - Page 13
...repaired in -warranty service.
Consumable parts are unable to resolve
the problem after checking "Troubleshooting," additional help you obtain assistance or service if you need for in your major appliance to correct the installation of your retailer about the quality, durability, or need repair service, first see the "Troubleshooting" section of products not approved by Whirlpool...
Warranty Information - Page 1
... operated, and maintained according to instructions attached to or furnished with Whirlpool published installation instructions.
10. If you should ask Whirlpool or your retailer about your major appliance is located in this Warranty. Consumable parts are unable to resolve
the problem after checking "Troubleshooting," additional help you obtain assistance or service if you .
You can...
Installation Guide - Page 4
.... Read and follow the instructions provided with clothes dryers. Tape measure
Pliers
4
Tools needed : Check local codes. Mobile home installations require metal exhaust system hardware, available for use with any tools listed here. For further information, please reference the "Assistance or Service" section of the "Use and Care Guide". Check existing electrical supply and venting...
Installation Guide - Page 5
... closets, mobile homes, or sleeping quarters.
See "Electrical Requirements."
■■ A sturdy floor to match height of 1" (25 mm) under entire dryer. (If slope is available for mobile home installations. Recessed area B. capacity washer) or 1½" (38 mm) (to support the total weight (dryer and load) of the dryer in .2 * (155 cm )2
1"
29"
1" 1"* 27¾"
(25...
Installation Guide - Page 13
...codes and ordinances.
Only rigid or flexible metal vent shall be fully extended and supported in final dryer location. ■■ Remove excess to avoid
crushing and kinking.
Dryer exhaust must not be connected into interior of a building. Rigid metal vent: ■■ Recommended for more information. 13
Replace...not install in... performance. Review "Vent System ...
Installation Guide - Page 16
...Care Guide". q For power supply cord installation, plug into an outlet and/or electrical ...Dryer". q Set the dryer on power. If the dryer will not start the dryer. Dryer vent must be level for
20 minutes and start , check the following: ■■ Controls are level, make sure vent is level. Avoid crushing or kinking vent.
After dryer is closed. If you have all parts...
Dimension Guide - Page 1
... installation The dimensions shown following are required. Recessed area B. Louvered doors with equivalent ventilation openings are acceptable.
■■ Companion appliance spacing should be 1/2" (13 mm) (to match height of 3.6 cu. Side view - closet or confined area C. ft.
Closet door with elbow. Dryer Dimensions
29" (737 mm)
433/8" (1102 mm)
Electric Dryer
PRODUCT MODEL...
Dimension Guide - Page 2
...installation to use . For complete details, see Installation Instructions ...dryer to change without notice. Vent System Chart (Long Vent Models Only)
Number of 90° turns or elbows
Type of dryer...24.4 m)
5
Rigid metal
70 ft. (21.3 m)
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we ...is required. Specifications subject to avoid kinking....
Whirlpool WED4810BQ Reviews
We have not received any reviews for Whirlpool yet.