Whirlpool UXD8636DY Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool UXD8636DY manuals!
Problems with Whirlpool UXD8636DY?
Ask a Question
Free Whirlpool UXD8636DY manuals!
Problems with Whirlpool UXD8636DY?
Ask a Question
Popular Whirlpool UXD8636DY Manual Pages
Owners Manual - Page 3
...safety messages in this manual and on your appliance. All safety messages will tell you what can kill or hurt you how to potential hazards that can happen if the instructions are very important..... These words mean:
DANGER
You can be killed or seriously injured if you don't follow instructions. VENT SYSTEM SAFETY
Your safety and the safety of others . WARNING
You can be killed ...
Owners Manual - Page 5
... the front of the cooktop. The model/serial/rating plate is installed directly behind the cooktop.
See the "Countertop Cutout Dimensions" section. IMPORTANT: Observe all governing codes and ordinances.
■■ Have a qualified technician install the downdraft vent. INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before making any tools listed here...
Owners Manual - Page 7
... with your specific installation. Countertop and backsplash I
A. see the following illustrations. Measurement of cooktop cutout
NOTES:
■■ See cooktop manufacturer's instructions for cooktop cutout...19.1 mm) maximum backsplash depth
C. 271/2" (69.9 cm) on 30" (76.2 cm) models 331/2" (85.9 cm) on the countertop before making any cutouts. The cutout locations for this...
Owners Manual - Page 8
... CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all governing codes and ordinances. If vent cutout falls over a joist or stud, a supporting frame must terminate to the requirements of the vent system.
The model/serial/rating plate is adequate and in the Installation Instructions. The specified CFM varies from :
National...
Owners Manual - Page 11
...the motor box and secure with vent cover screws. Bottom Venting: NOTE: If installing the vent damper in each support leg. Cover plate screws (4)
C. Motor mounting screws (4) E. Motor box G....Blower Motor" section. Vent cover plate F.
Install the vent cover plate over the keyhole slot shoulder screws. Blower Motor" section.
Cover plate
B. Set the cover aside.
4. Remove 3 screws and...
Owners Manual - Page 12
...blower motor rear-mounting position (opposite side) for island cabinet location. Remove 7 screws from blower motor and set the cover aside.
5. Keyhole slot shoulder screws (2)
A
C. 1/4" (6.4 mm) deep cover
C
B
... the ¼" (6.4 mm) deep cover off the shoulder screws in the keyhole slots and set blower motor box aside.
3. Rear Mounting - Remove the screws from the mounting flange of...
Owners Manual - Page 14
...recommended), using .
2. Refer to the vent opening
(left- Terminal box cover
3.
Lower support leg F. Attach the 3¼" x 10" (8.3 cm x 25.4 cm) backdraft damper
...1. Rear of downdraft vent B.
or right-side venting only is centered in countertop C. Cabinet floor G. Complete Installation
NOTE: The downdraft vent system is supplied with a 31/4" x 10" (8.3 cm x 25.4 cm) ...
Owners Manual - Page 15
...
Screw (not provided)
9. 5. Install the left and right end caps to lock into place. Loosen the lower support leg screws and position the legs ... Mounting slot
15 B
A
D
A. Fasten the lower support legs to set them in place. A
A. Check that will not allow...Slide the keyhole slots over the guide tabs and push the brackets up to the cabinet floor with screws (not provided)....
Owners Manual - Page 16
...Service" section. Blower control slider
D. Filters
2. Vent system must end with screw.
7. Install cooktop according to blower.
Black wires
E. Replace...C
E D
A. Connect vent system to manufacturer's instructions. UL listed wire connectors
D. Trim kits for a...Replace all joints.
5. Tighten the screw on the side of vent to seal all parts and panels before servicing...
Owners Manual - Page 17
...downdraft vent blower speed or increase the cooktop burner flame setting.
■■ For gas cooktops with flame-sensing ...When the filter is removed, the microswitch behind the filter is properly installed.
■■ Wipe with damp soft cloth or nonabrasive sponge,... SYSTEM CARE
Surface of downdraft vent will go. To Replace: 1. VENT SYSTEM USE
The retractable downdraft vent system...
Owners Manual - Page 18
... manual and scan the code there with the
raises
downdraft vent movement. Has the control slider been moved from the bottom of the vent box to remove any residue left by mail with the vent movement? Is the blower installed correctly? See the "Rear Mounting - Downdraft not level on the top of the support...
Owners Manual - Page 19
... GY RD RD WH WH BR BR
BR RD
N.O.
Plenum Up/Down
19 COM N.C. COM
5
N.C. GY
GY
N.O.
WIRING DIAGRAM
YL
7
BR
M YL/GN
S50
Motor Specifications
Power supply
120 VAC
Frequency
60 Hz
Wattage rating
420 W
Amperage
3.7 A
Motor Resistance
Blue - N.O. COM
4
N.C.
6
M SEL0015061B
Num.
1 2
3 4
5 6 7 8 9
GND L N
Note: Wiring Diagram is drawn with plenum...
Owners Manual - Page 20
...to order replacement parts, we recommend that you can write to Whirlpool Canada LP with each kit. To locate factory specified replacement parts in Canada.
■■ Features and specifications on our full line of service.
For model series UXD8630DY 30" (76.2 cm) one-piece top trim Order Part Number W10387678 (black) Order Part Number W10388421 (white)
For model series UXD8636DY 36...
Owners Manual - Page 21
...of original purchase date is installed,
installation instructions. In the U.S. If outside the 50 United States or Canada, contact your appliance will pay for appliances with servicing, removal or replacement of non-genuine Whirlpool parts or accessories.
6.
Specified Replacement Parts and repair 4. labor to review the Troubleshooting or Problem Solver section of purchase...
Owners Manual - Page 44
Utilisé sous licence au Canada. Tous droits réservés.
12/16 Used under license in Canada. All rights reserved. W10342491F
®/™ ©2016 Whirlpool.
Whirlpool UXD8636DY Reviews
We have not received any reviews for Whirlpool yet.