Whirlpool GI15NDXTB - 15" 50 lb. Icemaker Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool GI15NDXTB manuals!
Problems with Whirlpool GI15NDXTB?
Ask a Question
Free Whirlpool GI15NDXTB manuals!
Problems with Whirlpool GI15NDXTB?
Ask a Question
Most Recent Whirlpool GI15NDXTB Questions
Whirlpool Undercounter Ice Maker Wont Open Water Valve
(Posted by scorpleet 9 years ago)
Gi15ndxtq1 Whirlpool Ice Maker.
I recently had to change the recirc. pump. Now, the ice maker forms ice on the platten but then neve...
I recently had to change the recirc. pump. Now, the ice maker forms ice on the platten but then neve...
(Posted by crumbcrusher58 11 years ago)
Why Do The Ice Maker Keep Dumping Water
(Posted by robertm01 13 years ago)
Popular Whirlpool GI15NDXTB Manual Pages
Use and Care Guide - Page 3
... or glue residue can damage the surface of your ice maker before servicing. These words mean:
DANGER
You can result in back or other injury. IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using . SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Unpack the Ice Maker
WARNING
Excessive Weight Hazard Use two or more people...
Use and Care Guide - Page 4
... the drain line (on the top and three sides, but the installation should choose a location where the floor is equipped with the National Electrical Code and local codes and ordinances, is important for the ice maker to be pulled forward for proper ice maker operation.
See "Leveling."
s This unit must be completely unobstructed. Replace the filter if necessary.
4
Use and Care Guide - Page 5
... . Use shims to clear line of the ice maker.
Before purchasing, make several adjustments to its final location. Tighten packing nut. s Ensure that side of water.
2. Pipe clamp C. Coupling (purchased)
D
E. Compression nut F.
Leave a coil of the pipe, not the bottom. Follow the instructions in installation, move the ice maker as close as it . Use a carpenter's level...
Use and Care Guide - Page 6
... cabinet's side wall or other parts inside diameter. Do not use an adapter. Then tighten it with a 1¹⁄₂" (3.81 cm) to the drain inlet.
If the ice maker is adequate, follow these instructions can settle.
Do not overtighten. Coupling (purchased)
D EF G
E. This will not work. s The ideal installation has a standpipe with a wrench two...
Use and Care Guide - Page 7
.... 2. B
s Move the bottom end cap diagonally to move and install ice maker. Set the door aside. Hinge pin sleeve C. For gravity drain system, push the ice maker into the top hinge.
5. Unscrew and remove the top hinge.
Replace the handle and handle screws. Keep the parts together and set them aside. Hex-head hinge screw
3. Remove the hinge pin...
Use and Care Guide - Page 8
... the water are not familiar to you might be making cycle. 5. IMPORTANT: s If the water supply to the ice maker is turned off automatically and restarts when more ice is programmed to follow these instructions can make a splashing sound. The Ice Making Process 1. When the desired thickness is reached, the ice sheet is constantly circulated over the condenser by...
Use and Care Guide - Page 9
...ice maker. Remove all handling information on the water pan. Replace...Service Light
The service light indicates when service is complete. The light will both clean and rinse itself.
8. ICE MAKER CARE
Cleaning
The ice making cycle, select ON. 2. Ice Maker...ice maker to operate at peak efficiency and to avoid premature failure of 15... thin ice or no ice.
5. Look for Part Number 4396808...
Use and Care Guide - Page 10
...which may lead to remove the lower access panel. 3. Replace the drain cap securely on the bottom back side.
5. Replace all parts and panels before cleaning. Pull forward to component failure. ...Replace the lower access panel using the four screws. 6.
Water pan B. Drain cap
10 Unplug ice maker or disconnect power. 2. Failure to remove the lower access panel. Screws
6. NOTE: Make...
Use and Care Guide - Page 11
.... To shut down the ice maker: 1. They cannot withstand temperatures above 145°F (63°C).
11. Disconnect the inlet and outlet lines to water valve. Plug into storage bin drain opening.
13.
s Replace the ice scoop holder by removing the two thumb screws. Check the following instructions. Remove all parts and panels before servicing. If the room...
Use and Care Guide - Page 12
... the drain tube? Make sure the water supply is still water in the bin, check to follow these instructions can result in the ice maker? s Is there debris in the reservoir overflowing? Room temperatures of ice. TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call an electrician.
Be...
Use and Care Guide - Page 13
...purchase date and the complete model and serial number of "Cleaning" for assistance or service, please check "Troubleshooting." To locate FSP® replacement parts in place? s Installation information. s Referrals to align the drain. For further assistance If you need further assistance, you the cost of the ice maker. s Accessory and repair parts sales.
See "Interior Components" section...
Use and Care Guide - Page 14
... WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. Service calls to correct the installation of your major appliance, to instruct you how to parts or systems resulting from warranty coverage.
3. Repairs to use of products not approved by Whirlpool.
5. This limited warranty...
Dimensions - Page 1
...; Ice Maker
PRODUCT MODEL NUMBERS
GI15NDXT GI15NFLT GI15NFRT
Electrical: 115 volt, 60 Hz, AC only, 15 or 20-amp grounded circuit is recommended. Drain: Either a gravity-drain system or condensate pump to carry water to the drain inlet. For complete details, see Installation
our products, we reserve the right to change materials and specifications without notice. Instructions packed...
Whirlpool GI15NDXTB Reviews
We have not received any reviews for Whirlpool yet.