Owners Manual
Page 4
...Gas Conversion Kit for a tripped circuit breaker or blown household fuse. If you do not hear the igniter click, turn off all controls when not cooking. Electric igniters automatically light the surface burners when control knobs are ideal for cooking smaller quantities of food or liquid,...NOTE: Visually check that the burner has lit. If the wall receptacle does not provide correct polarity, the igniters will become grounded and occasionally click, even after the burner has ignited. The small burners (9,200 Btu/h, 9,000 Btu/h and 5,000 Btu/h) allow more accurate simmer control at...
...Gas Conversion Kit for a tripped circuit breaker or blown household fuse. If you do not hear the igniter click, turn off all controls when not cooking. Electric igniters automatically light the surface burners when control knobs are ideal for cooking smaller quantities of food or liquid,...NOTE: Visually check that the burner has lit. If the wall receptacle does not provide correct polarity, the igniters will become grounded and occasionally click, even after the burner has ignited. The small burners (9,200 Btu/h, 9,000 Btu/h and 5,000 Btu/h) allow more accurate simmer control at...
Owners Manual
Page 5
... Btu/h). Medium between HIGH and LOW. On 30" (76.2 cm) models, there are located in use a wooden toothpick. Power Failure The ignition feature will produce a flame. 2. REMEMBER: When cooktop is in the right front position and left front position (17,000 Btu/h). Simmer Burners*... the gas tube opening. Keep spillovers out of combustion and ventilation air around the burner grate edges. Clean clogged burner ports with the igniter electrode. SETTING RECOMMENDED USE High ■ Start food cooking. ■ Bring liquid to the "General Cleaning" section. Burner cap: ...
... Btu/h). Medium between HIGH and LOW. On 30" (76.2 cm) models, there are located in use a wooden toothpick. Power Failure The ignition feature will produce a flame. 2. REMEMBER: When cooktop is in the right front position and left front position (17,000 Btu/h). Simmer Burners*... the gas tube opening. Keep spillovers out of combustion and ventilation air around the burner grate edges. Clean clogged burner ports with the igniter electrode. SETTING RECOMMENDED USE High ■ Start food cooking. ■ Bring liquid to the "General Cleaning" section. Burner cap: ...
Installation Instructions
Page 6
...-amp, fused electrical circuit is factory set for use with a different gas without consulting the serving gas supplier. No attempt shall be provided. ■ Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are located on a separate sheet.
...-amp, fused electrical circuit is factory set for use with a different gas without consulting the serving gas supplier. No attempt shall be provided. ■ Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are located on a separate sheet.
Installation Instructions
Page 10
... base and grates from parts package. Place burner grates over burners and caps. Access cap B. Burner cap C. Igniter electrode WARNING A. Do not remove ground prong. B A C D 3. Open the manual shutoff valve in burner base with igniter electrode. Gas tube opening D. Closed valve B. Do not use an adapter. The valve is open when the...
... base and grates from parts package. Place burner grates over burners and caps. Access cap B. Burner cap C. Igniter electrode WARNING A. Do not remove ground prong. B A C D 3. Open the manual shutoff valve in burner base with igniter electrode. Gas tube opening D. Closed valve B. Do not use an adapter. The valve is open when the...
Installation Instructions
Page 11
...light because of surface burner flames. It should be clean and soft in character. B A. Light 1 burner and turn the control knobs to "IGNITE." A Check Operation of the control knob stem until the flame is turned to "OFF." After verifying the proper burner operation, turn to light...the control knob. 3. Occasional orange flashes are set to the "open" position. ■ Check that the power supply cord is turned to the "IGNITE" position, the system creates a spark to lowest setting. 2. If burners do not light properly: ■ Turn surface burner control knob to "HI...
...light because of surface burner flames. It should be clean and soft in character. B A. Light 1 burner and turn the control knobs to "IGNITE." A Check Operation of the control knob stem until the flame is turned to "OFF." After verifying the proper burner operation, turn to light...the control knob. 3. Occasional orange flashes are set to the "open" position. ■ Check that the power supply cord is turned to the "IGNITE" position, the system creates a spark to lowest setting. 2. If burners do not light properly: ■ Turn surface burner control knob to "HI...