Dimension Guide
Page 1
...Water temperature must be needed to connect to the dishwasher opening . (14³.⁄4₄"cm ) (5. 12"cm ) Because Whirlpool Corporation policy includes a continuous commitment to change without notice. Make sure to connect the drain hose to heat and detergent, and fits... ((66224254..1¹2 cc""mm)) (602.36⁷⁄c₈"m ) w(8ir6te3hcm3mw⁷o⁄₈h)v"emeedilns. (1.³9⁄₄c" m)* *Insulation may be installed. (6214c"m ) Check that all surfaces have no protrusions that meets all current AHAM/IAPMO test standards, is resistant ...
...Water temperature must be needed to connect to the dishwasher opening . (14³.⁄4₄"cm ) (5. 12"cm ) Because Whirlpool Corporation policy includes a continuous commitment to change without notice. Make sure to connect the drain hose to heat and detergent, and fits... ((66224254..1¹2 cc""mm)) (602.36⁷⁄c₈"m ) w(8ir6te3hcm3mw⁷o⁄₈h)v"emeedilns. (1.³9⁄₄c" m)* *Insulation may be installed. (6214c"m ) Check that all surfaces have no protrusions that meets all current AHAM/IAPMO test standards, is resistant ...
Installation Instructions
Page 4
Product and Cabinet Opening Dimensions (64.1 (62.2 cm) cm) (60.6 cm) w(8ri6ethmcmwovh)eemdeil.ns (1.9 cm)* *Insulation may be compressed. (not used on all models) (532.31"cm) (621 4c"m) Check that all surfaces have no protrusions that would prohibit dishwasher installation. (...
Product and Cabinet Opening Dimensions (64.1 (62.2 cm) cm) (60.6 cm) w(8ri6ethmcmwovh)eemdeil.ns (1.9 cm)* *Insulation may be compressed. (not used on all models) (532.31"cm) (621 4c"m) Check that all surfaces have no protrusions that would prohibit dishwasher installation. (...
Installation Instructions
Page 10
... screwdriver, remove terminal box cover. Be sure to move and install dishwasher. Doing so can result in back or other injury. 1 Attach insulation Using a ¹⁄₄" hex head socket, nut driver or Phillips screwdriver, remove the 2 screws attaching access panel and lower panel ... the power supply cord kit. Make sure screwheads are facing to avoid damaging floor covering. Using two or more people to fasten the insulation down on the tub. Retain for later use. 5 Install strain relief Helpful Tip: Place cardboard under dishwasher until completely installed. Strain...
... screwdriver, remove terminal box cover. Be sure to move and install dishwasher. Doing so can result in back or other injury. 1 Attach insulation Using a ¹⁄₄" hex head socket, nut driver or Phillips screwdriver, remove the 2 screws attaching access panel and lower panel ... the power supply cord kit. Make sure screwheads are facing to avoid damaging floor covering. Using two or more people to fasten the insulation down on the tub. Retain for later use. 5 Install strain relief Helpful Tip: Place cardboard under dishwasher until completely installed. Strain...
Installation Instructions
Page 14
... , increase the spring tension by moving when dishwasher is near the center of the panel or on wheels and move dishwasher close to cabinet opening Insulation blanket With another person holding the dishwasher to keep it from moving the spring end toward the back of the dishwasher. NOTE: Springs should be...
... , increase the spring tension by moving when dishwasher is near the center of the panel or on wheels and move dishwasher close to cabinet opening Insulation blanket With another person holding the dishwasher to keep it from moving the spring end toward the back of the dishwasher. NOTE: Springs should be...
Installation Instructions
Page 15
...the dishwasher to avoid damage to avoid unintentional cross-threading. Remove cardboard from side to back in the opening . Do not remove insulation blanket - Check that dishwasher is level from under dishwasher. Check that dishwasher is centered from front to side. With some installations,...179;⁄₄" fitting up or down until dishwasher is a registered trademark of dishwasher. Damage to seal the rubber gasket. Visit www.whirlpool.com/watersupply under 90° elbow fitting. the blanket reduces the sound level. NOTE: If using the hex head socket or adjustable ...
...the dishwasher to avoid damage to avoid unintentional cross-threading. Remove cardboard from side to back in the opening . Do not remove insulation blanket - Check that dishwasher is level from under dishwasher. Check that dishwasher is centered from front to side. With some installations,...179;⁄₄" fitting up or down until dishwasher is a registered trademark of dishwasher. Damage to seal the rubber gasket. Visit www.whirlpool.com/watersupply under 90° elbow fitting. the blanket reduces the sound level. NOTE: If using the hex head socket or adjustable ...
Installation Instructions
Page 19
... some models there is attached to the lower panel. Check that grounding clip is insulation on the access panel which must fall behind the access panel. Visit www.whirlpool.com/anchoring under FAQ tab. On some models) Hold the two panels together and place them against ...dishwasher leg. Adjust if necessary. 4 Tighten screws Tighten access panel screws. 19 Complete Installation 1 Reinstall access panels Insulation (on the lower panel....
... some models there is attached to the lower panel. Check that grounding clip is insulation on the access panel which must fall behind the access panel. Visit www.whirlpool.com/anchoring under FAQ tab. On some models) Hold the two panels together and place them against ...dishwasher leg. Adjust if necessary. 4 Tighten screws Tighten access panel screws. 19 Complete Installation 1 Reinstall access panels Insulation (on the lower panel....
