Weider D485 Cobra Plus Support and Manuals
Get Help and Manuals for this Weider item
This item is in your list!
View All Support Options Below
Free Weider D485 Cobra Plus manuals!
Problems with Weider D485 Cobra Plus?
Ask a Question
Free Weider D485 Cobra Plus manuals!
Problems with Weider D485 Cobra Plus?
Ask a Question
Popular Weider D485 Cobra Plus Manual Pages
Assembly Instructions - Page 1
D480
101i
D480/485 ASSEMBLY INSTRUCTIONS
RECOMMENDED WEIGHT SET - 365 LBS. rr
D485
o 'O',31.71 1.
REPLACEMENT PARTS
NN-1107
WEIDER HEALTH AND FITNESS
21100 ERWIN STREET, WOODLAND HILLS, CA., 91367
Assembly Instructions - Page 2
... CAREFULLY, PAYING PARTICULAR ..ATTENTION TO ALL WARNINGS, CAUTIONS, NOTES OR NOTICES LAY OUT UNASSEMBLED PARTS: FAMILIARIZE YOURSELF WITH THE DRAWINGS THEN READ AND UNDERSTAND. THE INSTRUCTIONS THOROUGHLY. 2. DO NOT DESTROY THE INSTRUCTION MANUAL USE IT FOR ORDERING REPLACEMENT PARTS A RECOMMENDED TOOLS FOR PROPER ASSEMBLY ARE AS FOLLOWS: A HAMMER, PLIERS, MEDIUM SIZE FLATHEAD SCREWDRIVER...
Assembly Instructions - Page 3
...
t areckot. To lower hole, bolt WEIGHT HOLDER BRACKET (10) to FRONT SUPPORT (6) with bolt holes. Insert 2" SQUARE PLASTIC CAPS (37) into each end of FRONT SUPPORT (6).
48 42
-
5
Insert 1 3/4" SPACER (20) into end of ... ,,•=e1
5
4 3
STEP 2 MAIN FRAME ASSEMBLY
Assemble FRONT SUPPORT (6) to Uprights using 6/16" X 3' HEX HEAD BOLTS (32), 5/16" FLAT WASHERS (33) and 6/16" LOCK NUTS (34...
Assembly Instructions - Page 4
... 19 20 21 25 26
PART NAME
UPRIGHT
CROSS MEMBER
MAIN FRAME
BASE (RIGHT)
BASE (LEFT)
FRONT SUPPORT
020410,-AbIGLEARON
BACKREST
SEAT
WEIGHT HOLDER BRACKET
LEG CURL
LEG CURL BRACKET
WEIGHT PIN
C/OZ. X 2 1/2' CARRIAGE BOLT
1
47
5/16'-18 X 4 1/r HEX HEAD BOLT
1
48
5/1V-18 X 3 1/4' HEX HEAD BOLT
2
INSTRUCTION MANUAL
1
EXERCISE CHART
1
1
07-27-90...
Assembly Instructions - Page 5
...UPRIGHTS (1) to adjust BACKREST (8) to allow enough clearance so that the threaded shaft on SEAT SUPPORT BRACKETS (25) and secure with the holes in
the front of BACKREST ADJ BAR (17)... LOCK NUTS (34) to a desired incline.
STEP 3 SEAT & BACKREST ASSEMBLY
SEAT: Loosely assemble SEAT SUPPORT BRACKETS (26) and (26) to
the rear of the positioning holes along MAIN FRAME (3). Tighten Seat ...
Assembly Instructions - Page 6
...procedure and
assemble 4' X 6" FOAM PADS (16) to
Longer PAD BARS (21) and assemble
them to FRONT SUPPORT (6) with 2" SQUARE PLASTIC 9
16
CAP (37). Assemble 2 1/2' X 7" FOAM PAD (16) on ..." LOCK NUT (34). Insert 3/4" ROUND PLASTIC
CAP (39) into Pad Bar Hole in FRONT SUPPORT
6
(6). CIS::::.. SECURE WEIGHTS ON tea CURL
WEIGHT PINS.
5 use Lamm' COLLARS FROM DUMBBELLS TO. FLAT WASHER ...
Assembly Instructions - Page 7
...with
another FLAT WASHER (33) and 6/16' LOCK NUT (34) and tighten just enough to fasten DUMBBELL HANDLE (49). D485 (COBRA PLUS) SUPPLEMENTAL PARTS LIST
DIAGRAM NO 22 23 24
30 33 34 40 49 50 51 52 53 54 55 56 57 58...
PART NAME FLY ARM PIVOT TUBE WEIGHT STACK PIN (1' X 8') HARDWARE BAG 5/16%18 X 2 1/2' HEX BOLT 5/16' FLAT WASHER 5/16'...
Weider D485 Cobra Plus Reviews
Do you have an experience with the Weider D485 Cobra Plus that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Weider yet.
Earn 750 points for your review!