Weider 8925hard Drive Sys Support and Manuals
Get Help and Manuals for this Weider item
This item is in your list!
View All Support Options Below
Free Weider 8925hard Drive Sys manuals!
Problems with Weider 8925hard Drive Sys?
Ask a Question
Free Weider 8925hard Drive Sys manuals!
Problems with Weider 8925hard Drive Sys?
Ask a Question
Popular Weider 8925hard Drive Sys Manual Pages
English Manual - Page 1
....
MST
CAUTION! Read all safety precautions and instructions in this owner's- --manual before using this owner's manual for future reference. The trained technicians on our customer hot line will guarantee you complete satisfaction through direct assistance from our factory.
As a manufacturer, we are missing or damaged parts, we will provide immediate assistance, free of...
English Manual - Page 2
... manual and in this product.
2 The weights will fall with pre-existing health problems. Read all instructions in the accompanying literature before using . CABLING DIAGRAM ORDERING REPLACEMENT PARTS ... at all parts each time you are exercising, stop immediately and begin cooling down. ASSEMBLY ADJUSTMENT TROUBLE-SHOOTING AND MAINTENANCE - Replace any worn parts immediately.
-,4.:...
English Manual - Page 3
..., the WEIDER 8925 will help us assist you for selecting the versatile WEIDER® 8925 Hard Drive System. The serial number can be found on a decal attached to achieve the specific results you have additional questions, please call our Customer Service Department toll-free at the drawing below and familiarize yourself with the parts that...
English Manual - Page 5
...
46
Guard Brackets (20) with two 5/16" Nylock Nuts (4). Insert a 5/16" x 2 1/2" Carriage Bolt (1) through the top hole in a Weight Tube (108).
5 145
Deepest Pin Groove "Weider"
Logo 107
6
1
Slide four Rollers (109) onto the short pins on the indicated side.
there is a 24" slot
4
in the Weight Tube (108). Make sure...
English Manual - Page 6
...sure that the pin grooves in the Base (15).
The Rear Upright must be turned so the "Weider" logo is on top, and the deepest pin groove is facing
down into each side of the...Rear Upright (17) with two 5/16" Nylock Nuts (4). Slide the Weight Tube down . Weights (107) so the "Weider" logo is facing the Weight Tube (see inset drawing B). Weight (145) onto the Rear Upright (17). 7. See ...
English Manual - Page 9
... Arm Tube to the Front Upright (19) with four 1/4" x 3/4" Screws (7), four 1/4" Flat Washers (6), and four 1/4" Nylock Nuts (5).
99--,
19
104-Grease
. •
12
._.,mot. 7
17. Set the Press Arm Bushings, the Press Arm Tube, the Press Arm (12), and the Thin
59---,›
Metal Plate (99) on the side shown. Attach...
English Manual - Page 10
.... The narrow end of the Short Arm Shock can be adjusted. Press a 1 1/2" Inner Cap (38) into the Seat Frame (32).
Align one of the three sets of a Short Arm Shock (25) with a 5/16" x 1 3/4" Bolt (106), a 5/16" Flat Washer (45), and a
5/16" Nylock Nut (4). 19
Attach the other Short Arm Shock (25...
English Manual - Page 18
If the cables do not move smoothly over the pulleys. Refer to TROUBLESHOOTING AND MAINTENANCE on page 22 to see the proper routing of all parts are not properly routed, they may be explained in the drawing below.
46 HIGH PULLEY
WEIDER 8925
RANGE OF MOTION
BUTTERFLY
c3 o
1 °
BENCH PRESS
SQUAT/MILITARY
... Make...
English Manual - Page 19
...
__The instructions below describe how each part of ...starting position for each exercise station may vary from the weight setting. SELECTING A WEIGHT SETTING
The hard drive system features dual weight stacks to allow two ...to 150 pounds, in the Front Upright (19).
Refer to the EXERCISE GUIDE accompanying this owner's manual to the high pulley station, the low pulley station, the leg lever...
English Manual - Page 22
...1/4" x 1/2" Tap Screw (68) near the
lower end of this owner's manual for information about ordering replacement parts.
68
69
Ball
Adjustment Sleeve
22
When the Weight Cable (70) is slack... of the Weight Cable. Follow the instructions below to be resting against the low pulley. TROUBLE-SHOOTING AND MAINTENANCE
Inspect and tighten all parts each time you use solvents.
See ...
English Manual - Page 24
... KEY NUMBER and DESCRIPTION of the part(s) from the date of purchase. This warranty extends only to state. No other warranty beyond that specifically set forth above is limited to replacing or repairing, at WEIDER's option, the product at one of its authorized service centers.
To help us assist you specific legal rights.
All returns must be prepared...
English Manual - Page 25
... 105 1 106 4
1/4" x 2 1/2" Screw 3/8" x 2 3/4" Bolt Foam Grip 1/2" x 3/8" Spacer Bar Holder Arm Frame Cap Arm Frame Bushing "J"-Pin Butterfly Seat 3/8" Nylock Nut 3/8" Flat Washer 3/4" Cover. PART LIST Model No. Description
Key No. Qty. Cap 1/4" x 1 1/4" Bolt 3 1/2" Pulley 1/4" x 1/2" Tap Screw Pulley Cable Weight Cable "L"-Bracket Lat Bar Chain Cable Clip Pivot Arm 3/8" x 1 3/4" Bolt Thin...
English Manual - Page 26
... 6 140 4 141 6 142 1 143 2 144 2 145 2 146 28 147 1 148 1 149 2 150 1
# 1 # 1 # 1 # 1
10 lb. Specifications are subject to change without notice. See the back cover of the owner's manual for information about ordering replacement parts. Part No. 122218 R994A© 1994 Weider, Inc. Key No. Qty.
Weight Weight Tube Roller Weight Bracket 1/2" x 1 3/4" Spacer Weight Pin 5/16...
English Manual - Page 29
This side of the chart shows all other parts. Cod
#8-32 Nut (143)-2
O
#8 Washer (144)-2
1/4" Nylon Lock Nut (5)-13... (63)-5
1/4" x 3/4" Screw (7)-16
1/4" x 2" Screw (82)-4 The second number refers to help identify the small parts used in parenthesis below each part refers of the key number of the nuts, washers and bolts used in assembly. WG89250 R794A
This chart is provided to the...
Weider 8925hard Drive Sys Reviews
Do you have an experience with the Weider 8925hard Drive Sys that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Weider yet.
Earn 750 points for your review!