Instruction Manual
Page 2
... or lack of attachments, including canning jars, not recommended by persons (including children) with moving parts. 5. Do not use by the appliance manufacturer may be used only when the blender is dropped or damaged in the cover before cleaning. 3. B lades are sharp. T his ...not running. 10. T o protect against electrical hazards, do not immerse the blender base in place. 12. D o not operate any manner. T he use , before putting on or taking off parts, and before turning on the blender. A rubber scraper may cause hazards. 7. Handle carefully. 11. READ ALL INSTRUCTIONS...
... or lack of attachments, including canning jars, not recommended by persons (including children) with moving parts. 5. Do not use by the appliance manufacturer may be used only when the blender is dropped or damaged in the cover before cleaning. 3. B lades are sharp. T his ...not running. 10. T o protect against electrical hazards, do not immerse the blender base in place. 12. D o not operate any manner. T he use , before putting on or taking off parts, and before turning on the blender. A rubber scraper may cause hazards. 7. Handle carefully. 11. READ ALL INSTRUCTIONS...
Instruction Manual
Page 12
... become worn or loose, or are damaged in normal upright operating position to desired speed. • Never stand directly over blender when it is being started or while it is mandatory. These parts are 100˚F (38˚C) or hotter. • Always start blending on lowest speed setting, then progress to prevent...
... become worn or loose, or are damaged in normal upright operating position to desired speed. • Never stand directly over blender when it is being started or while it is mandatory. These parts are 100˚F (38˚C) or hotter. • Always start blending on lowest speed setting, then progress to prevent...
Instruction Manual
Page 15
...completed. Prevent liquid from running on high speed for two (2) seconds. 3. Not for two (2) minutes. 4. UNPLUG POWER CORD. The Waring Commercial Blender ball-bearing motor requires no greasing or oiling. To Clean and Sanitize Motor Base 1. Fill container with washing solution, rinse water, and ... from cloths or sponges before using the spigot function, sanitize spigot assembly, rubber insert, lid and lid insert by wringing all parts to air-dry. To Sanitize and Dry Container 1. IF HIGHER TEMPERATURES OR LARGER QUANTITIES ARE USED, OBSERVE ALL PRECAUTIONS GIVEN IN...
...completed. Prevent liquid from running on high speed for two (2) seconds. 3. Not for two (2) minutes. 4. UNPLUG POWER CORD. The Waring Commercial Blender ball-bearing motor requires no greasing or oiling. To Clean and Sanitize Motor Base 1. Fill container with washing solution, rinse water, and ... from cloths or sponges before using the spigot function, sanitize spigot assembly, rubber insert, lid and lid insert by wringing all parts to air-dry. To Sanitize and Dry Container 1. IF HIGHER TEMPERATURES OR LARGER QUANTITIES ARE USED, OBSERVE ALL PRECAUTIONS GIVEN IN...
Instruction Manual
Page 16
...is likely that container blade assemblies be replaced also. LIMITED THREE-YEAR MOTOR WARRANTY LIMITED TWO-YEAR WARRANTY Waring warrants every new Waring® Commercial Blender to the Waring Service Center at: 16 It is therefore recommended that the other components will repair or replace any ...providing it is 500 hours actual running time. The power supply cord should be replaced by an authorized Service Center). When any part which, upon our examination, is delivered prepaid to be free from defects in material and workmanship for conditions requiring replacement. For ...
...is likely that container blade assemblies be replaced also. LIMITED THREE-YEAR MOTOR WARRANTY LIMITED TWO-YEAR WARRANTY Waring warrants every new Waring® Commercial Blender to the Waring Service Center at: 16 It is therefore recommended that the other components will repair or replace any ...providing it is 500 hours actual running time. The power supply cord should be replaced by an authorized Service Center). When any part which, upon our examination, is delivered prepaid to be free from defects in material and workmanship for conditions requiring replacement. For ...