Operation Manual
Page 7
... igniting the gasoline, place the container and/or mower directly on the ground before filling, not in an approved fuel container, out of the reach of SF, SG, SH, SJ, SL, or higher.) 3. Install the dipstick securely. Adjust the cutting height as the rear wheels (Figure 10). 7 Remove... the dipstick, wipe it with the moving parts to the fuel all moving blade, causing serious injury. • Stop the engine and wait for automotive use (87 pump octane minimum). Set the front wheels to check...
... igniting the gasoline, place the container and/or mower directly on the ground before filling, not in an approved fuel container, out of the reach of SF, SG, SH, SJ, SL, or higher.) 3. Install the dipstick securely. Adjust the cutting height as the rear wheels (Figure 10). 7 Remove... the dipstick, wipe it with the moving parts to the fuel all moving blade, causing serious injury. • Stop the engine and wait for automotive use (87 pump octane minimum). Set the front wheels to check...
Operation Manual
Page 8
...the mower, move the front cutting height levers rearward and the rear cutting height levers forward. Raise the mower Figure 10 2. Using the Self-propel Drive To operate the self-propel drive, simply walk with your hands on your sides, and the mower will automatically keep pace with... toggle switch (with you feel resistance, then pull it sharply (Figure 12). Pull the recoil starter lightly until you (Figure 13). 8 Lower the mower Note: The cutting height settings are 1 inch (25 mm); 1-3/8 inches (35 mm); 1-3/4 inches (44 mm); 2-1/8 inches (54 mm); 2-1/2 inches (64 mm); 2-7/8 ...
...the mower, move the front cutting height levers rearward and the rear cutting height levers forward. Raise the mower Figure 10 2. Using the Self-propel Drive To operate the self-propel drive, simply walk with your hands on your sides, and the mower will automatically keep pace with... toggle switch (with you feel resistance, then pull it sharply (Figure 12). Pull the recoil starter lightly until you (Figure 13). 8 Lower the mower Note: The cutting height settings are 1 inch (25 mm); 1-3/8 inches (35 mm); 1-3/4 inches (44 mm); 2-1/8 inches (54 mm); 2-1/2 inches (64 mm); 2-7/8 ...
Operation Manual
Page 13
...mower may plug and cause the engine to stall. • Mow only dry grass or leaves. Never deliberately mow over the lawn for damage. • For best performance, install a new blade before the cutting season begins. • Replace the blade when necessary with the blade. then mow again at a slower pace... objects with a Toro replacement blade. Mow only in dry conditions. • Be aware of a potential fire hazard in very dry conditions, follow all local fire warnings, and keep the mower free of the grass blade at the highest cutting height setting and walk slower; Figure 22...
...mower may plug and cause the engine to stall. • Mow only dry grass or leaves. Never deliberately mow over the lawn for damage. • For best performance, install a new blade before the cutting season begins. • Replace the blade when necessary with the blade. then mow again at a slower pace... objects with a Toro replacement blade. Mow only in dry conditions. • Be aware of a potential fire hazard in very dry conditions, follow all local fire warnings, and keep the mower free of the grass blade at the highest cutting height setting and walk slower; Figure 22...
Operation Manual
Page 14
You may need to make more than one pass over the leaves. • If there are more than the rear cutting height. • Slow down your mowing speed if the mower does not cut leaf cover. set the front cutting height one or two notches higher than 5 inches (13 cm) of the lawn shows through the cut the leaves finely enough. 14 Cutting Leaves • After cutting the lawn, ensure that half of leaves on the lawn, set the front wheels at 2-1/8-inch (54 mm) and the rear wheels at 2-1/2 inches (64 mm).
You may need to make more than one pass over the leaves. • If there are more than the rear cutting height. • Slow down your mowing speed if the mower does not cut leaf cover. set the front cutting height one or two notches higher than 5 inches (13 cm) of the lawn shows through the cut the leaves finely enough. 14 Cutting Leaves • After cutting the lawn, ensure that half of leaves on the lawn, set the front wheels at 2-1/8-inch (54 mm) and the rear wheels at 2-1/2 inches (64 mm).
Operation Manual
Page 18
... or blow out debris from the housing to cool before storing the mower in both the fully forward and fully rearward positions. 4. Lower the mower to prevent it for a few minutes to dry the housing to its lowest cutting height setting. Washout port Figure 32 18 Install the blade driver and disk that you...
... or blow out debris from the housing to cool before storing the mower in both the fully forward and fully rearward positions. 4. Lower the mower to prevent it for a few minutes to dry the housing to its lowest cutting height setting. Washout port Figure 32 18 Install the blade driver and disk that you...