TP-Link MC220L Support and Manuals
Get Help and Manuals for this TP-Link item
View All Support Options Below
Free TP-Link MC220L manuals!
Problems with TP-Link MC220L?
Ask a Question
Free TP-Link MC220L manuals!
Problems with TP-Link MC220L?
Ask a Question
TP-Link MC220L Videos
TP-LINK MC220L on innvisio.com
Duration: :19
Total Views: 92
Duration: :19
Total Views: 92
Popular TP-Link MC220L Manual Pages
MC200CM User Guide - Page 2
Copyright © 2011 TP-LINK TECHNOLOGIES CO., LTD.
is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. No part of the specifications may be reproduced in any form or by any derivative such as translation, transformation, or adaptation without notice. http://www.tp-link.com Other brands ...
MC200CM User Guide - Page 3
Installation Guides 5 4.1 Gigabit Ethernet Media Converter 5 4.2 Configuration 7 4.3 Installation Procedure 8 4.4 Install Media Converter into MC1400 9 5. Appendix: Specifications 11
i CONTENTS Package Contents 1 1. Introduction 1 2. Troubleshooting 10 6. Features 2 3. Appearance Indication 3
3.1 LED Indicators 3 3.2 Switch 4 4.
MC200CM User Guide - Page 4
... for larger bandwidth, and higher speed demanding workgroups that require expansion of MC220L supports hot-swappable. Introduction
MC200CM, MC210CS and MC220L are Gigabit Ethernet Media Converters.
The FX port of the Gigabit Ethernet network
Rear Panel
Front Panel
MC200CM&MC210CS 1 The converter mediates between a 1000Base-TX segment and a 1000Base-X segment. It is what you...
MC200CM User Guide - Page 5
... Full-Duplex mode for both TX port and FX port. ¾ Support auto MDI/MDIX for TX port. ¾ Extend fiber distance up to monitor network activity easily. ¾ External power supply.
2 Please check the table in page 3 for the accurate connector of each model. ¾ Easy-to-view LED indicators provide status to 0.55km...
MC200CM User Guide - Page 6
...MC220L
Interface
RJ45--SC RJ45--SC RJ45--LC
Transmission Distance
0.55km(50/125um) 0.22km(62.5/125um) 15km
0.55km/10km
Transmission Media
Multi-mode Fiber,TP Single-mode Fiber,TP
Multi/single-mode
Output Center Wavelength
850nm
1310nm
850nm/1310 nm
SC fiber connector and LC fiber connector
3. Connectors and Network Cables Supported
The connectors and network cables supported by the converter...
MC200CM User Guide - Page 7
... Guide Manual stands for TP Port. On LINK
Off
TP
On
RX Off
There's a valid link for the TX port without any explanations.
3.2 Switch
Force
AUTO
¾ FORCE: The FX port operates in FORCE mode.
4 There's no valid link for TP Port. The converter.... PWR
RX
LINK
LINK
FX TP
Name Status Indication
On Power on your network. The converter is receiving data from TP port.
MC200CM User Guide - Page 8
...: Be sure the opposite end is using two converters at the same time, the two converters must be set to FORCE mode. Transmits and receives data on AUTO. When using the same setting. SL2210WEB or TL-SL2428WEB, the converter must be set to Auto- Installation Guides
4.1 Gigabit Ethernet Media Converter:
¾ The SC fiber connector of MC200CM transmits/receives data by 850nm...
MC200CM User Guide - Page 9
Plug the SFP module into MC220L
Transmits and receives data between two MC220L Note: Two MC220L with two kinds of SFP modules, single-mode or multi-mode. Note: Either two MC200CM or two MC210CS could cooperate.
6
MC220L can be plugged in with the same SFP module could cooperate.
MC200CM User Guide - Page 10
... MC200CM or MC210CS, however, the SFP module in MC220L must use the same mode and the same wavelength as the opposite end. (Please refer to achieve the aim of effectively expanding a Gigabit Ethernet network, please take the following end devices.
7
Place two converters back to back between MC220L and MC200CM/MC210CS
Note:
MC220L could be LC-SC fiber. Model No.
MC200CM User Guide - Page 11
... other end of the Cat.5 twisted pair cable (Category-5) between 2 Media Converters, please refer to connection diagram in 4.1 ---- Connect one converter directly
between a 1000Base-TX network and a fiber optic (FX) device.
4.3 Installation Procedure
Use a fiber cable to connect two converters, or connect a converter with another MC200CM/MC210CS. 2. Note: For the correct connection between the...
MC200CM User Guide - Page 12
... Media Converter you will see the Media Converter's 9 Connection of a Converter and a 1000Base-FX Device.
3. Turn on the power.
4.4 Install Media Converter into MC1400
Tweak out the two screws located on either side of the chassis, and use them to connect the two Converters' SC connectors or the SC connecters of two Converters or a Converter and a 1000Base- FX Device: Use a SC fiber...
MC200CM User Guide - Page 13
... there is 1000M. 3. LINK LED (TP port) is off : 1) Check the fiber mode and fiber type to make sure that whether the
power lead is off: The power error. Troubleshooting
If you encounter some problems when you can operate it still doesn't work, please contact your dealer or ask for help from our technical support. 1. Please check...
MC200CM User Guide - Page 14
... Protocols Media Interface Max. 6. Distance Power Temperature
Humidity
MC210CS IEEE802.3ab, IEEE 802.3z, IEEE 802.3x SC, RJ45 Cat.5: 100m Single-mode Fiber: 15km External Power Adapter Operation: 0℃~40℃ Storage: -40℃~70℃ Operation: 10%~90% non-condensing Storage: 5%~90% non-condensing
11 Appendix: Specifications
Standards and Protocols Media Interface...
MC200CM User Guide - Page 15
Distance Power Temperature
Humidity
MC220L IEEE802.3ab, IEEE 802.3z, IEEE 802.3x LC, RJ45 Cat.5: 100m Multi/Single-mode Fiber: 0.55km/10km External Power Adapter Operation: 0℃~40℃ Storage: -40℃~70℃ Operation: 10%~90% non-condensing Storage: 5%~90% non-condensing
12 Standards and Protocols Media Interface Max.
TP-Link MC220L Reviews
We have not received any reviews for TP-Link yet.