Integrated Installation Guide
Page 2
INTEGRATED REFRIGERATION Contents 3 Integrated Refrigeration 4 Opening Dimensions 5 Electrical 5 Plumbing 6 Preparation 6 Anti-Tip Bracket 8 Placement 8 Alignment 9 Water Line 10 Custom Panels 12 Panel Installation 14 Completion Features and specifications are subject to -date information. IMPORTANT NOTE: Throughout this guide: IMPORTANT NOTE highlights information that may occur if instructions are millimeters unless otherwise specified. Visit subzero.com/specs for the local electrical inspector. WARNING states a hazard that is especially...
INTEGRATED REFRIGERATION Contents 3 Integrated Refrigeration 4 Opening Dimensions 5 Electrical 5 Plumbing 6 Preparation 6 Anti-Tip Bracket 8 Placement 8 Alignment 9 Water Line 10 Custom Panels 12 Panel Installation 14 Completion Features and specifications are subject to -date information. IMPORTANT NOTE: Throughout this guide: IMPORTANT NOTE highlights information that may occur if instructions are millimeters unless otherwise specified. Visit subzero.com/specs for the local electrical inspector. WARNING states a hazard that is especially...
Integrated Installation Guide
Page 3
If service is located inside the middle drawer near the drawer guide opposite the hinge. t Tubing cutter. t Saddle valve. t Material to the illustrations below. RATING PLATE RATING PLATE Column models. subzero.com | 3 t Drill bits (masonry bits required for questions regarding the installation, visit the contact & support section of 1/4" OD copper, braided stainless steel or PEX tubing. t 3' (.9 m) of our website, subzero.com or call Sub-Zero customer care at 800-222-7820...
If service is located inside the middle drawer near the drawer guide opposite the hinge. t Tubing cutter. t Saddle valve. t Material to the illustrations below. RATING PLATE RATING PLATE Column models. subzero.com | 3 t Drill bits (masonry bits required for questions regarding the installation, visit the contact & support section of 1/4" OD copper, braided stainless steel or PEX tubing. t 3' (.9 m) of our website, subzero.com or call Sub-Zero customer care at 800-222-7820...
Integrated Installation Guide
Page 5
.... Water supply location (bottom). SITE PREPARATION Electrical Installation must comply with all applicable plumbing codes. WARNING Do not use self-piercing valves. A ground fault circuit interrupter (GFCI) is not recommended for Connection 36" (914) WATER SUPPLY LOCATION WIDTH 18" Models 24" Models 30" Models 36" Models A 3" (76) 51/2" (140) 6" (152) 9" (229) LEFT SIDE OF OPENING 41/2" (114) A FLOOR 1/4" (6) FRONT VIEW 41/4" (108) Electrical supply location. Column and tall models with all applicable electrical codes. ELECTRICAL REQUIREMENTS Power Supply...
.... Water supply location (bottom). SITE PREPARATION Electrical Installation must comply with all applicable plumbing codes. WARNING Do not use self-piercing valves. A ground fault circuit interrupter (GFCI) is not recommended for Connection 36" (914) WATER SUPPLY LOCATION WIDTH 18" Models 24" Models 30" Models 36" Models A 3" (76) 51/2" (140) 6" (152) 9" (229) LEFT SIDE OF OPENING 41/2" (114) A FLOOR 1/4" (6) FRONT VIEW 41/4" (108) Electrical supply location. Column and tall models with all applicable electrical codes. ELECTRICAL REQUIREMENTS Power Supply...
Integrated Installation Guide
Page 8
... position, secure the door/ drawers closed and protect any finished flooring. Alignment LEVELING Once the unit is positioned. Do not turn clockwise to raise the unit or counterclockwise to be in position, height adjustment can be adjusted from the front once the unit is in contact with the floor. Rear adjustment. 8 | Sub-Zero Customer Care 800.222.7820 INSTALLATION Placement CAUTION Before moving...
... position, secure the door/ drawers closed and protect any finished flooring. Alignment LEVELING Once the unit is positioned. Do not turn clockwise to raise the unit or counterclockwise to be in position, height adjustment can be adjusted from the front once the unit is in contact with the floor. Rear adjustment. 8 | Sub-Zero Customer Care 800.222.7820 INSTALLATION Placement CAUTION Before moving...
Integrated Installation Guide
Page 9
... Panel thickness. Connect the plastic tubing from installing the new water line. Unit depth. This will remove any debris that may need to be exposed to freezing temperatures. INSTALLATION Alignment DEPTH ADJUSTMENT Adjust the depth of the unit to fit flush with the fitting connection kit provided. Place the panel thickness gauge next to the panel to access the handle side screw location. Insert a #8 x 1/2" stainless steel screw above the hinge, then insert a #8 x 1/2" pan...
... Panel thickness. Connect the plastic tubing from installing the new water line. Unit depth. This will remove any debris that may need to be exposed to freezing temperatures. INSTALLATION Alignment DEPTH ADJUSTMENT Adjust the depth of the unit to fit flush with the fitting connection kit provided. Place the panel thickness gauge next to the panel to access the handle side screw location. Insert a #8 x 1/2" stainless steel screw above the hinge, then insert a #8 x 1/2" pan...
Integrated Installation Guide
Page 10
... Sub-Zero dealer. DUAL INSTALLATION When installing two units side by side in the chart below. Dual installation kits are available through an authorized Sub-Zero dealer. Stainless steel panels are recommended. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820. 10 | Sub-Zero Customer Care 800.222.7820 Door handles must be located near the top edge of the two units added together. PANEL INSTALLATION Custom Panels For integrated models, custom door panels and handle...
... Sub-Zero dealer. DUAL INSTALLATION When installing two units side by side in the chart below. Dual installation kits are available through an authorized Sub-Zero dealer. Stainless steel panels are recommended. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820. 10 | Sub-Zero Customer Care 800.222.7820 Door handles must be located near the top edge of the two units added together. PANEL INSTALLATION Custom Panels For integrated models, custom door panels and handle...
Integrated Installation Guide
Page 12
... OF DOOR PANEL TOP OF DOOR PANEL 84" APPLICATION 83 7/8" ACTUAL USE TABS FOR HINGE SIDE PANEL EDGE ON DUAL INSTALLATION Door panel template-top. PANEL INSTALLATION Panel Installation DOOR PANEL INSTALLATION Typical panel dimensions are placed in the template with the bottom of the door panel, then mark and drill holes. Place the panel face down on both door mounting brackets. Align the support screws on the back of the panel during installation. Door panel mounting. 12 | Sub-Zero Customer Care...
... OF DOOR PANEL TOP OF DOOR PANEL 84" APPLICATION 83 7/8" ACTUAL USE TABS FOR HINGE SIDE PANEL EDGE ON DUAL INSTALLATION Door panel template-top. PANEL INSTALLATION Panel Installation DOOR PANEL INSTALLATION Typical panel dimensions are placed in the template with the bottom of the door panel, then mark and drill holes. Place the panel face down on both door mounting brackets. Align the support screws on the back of the panel during installation. Door panel mounting. 12 | Sub-Zero Customer Care...
Integrated Installation Guide
Page 14
... far to the handle side of tall and column models. Refer to the illustration below. Outer top trim. 14 | Sub-Zero Customer Care 800.222.7820 this trim strip fits on the trim strip to the handle side of the unit. Refer to the illustration below. DOOR TRIM Door trim. INSTALLATION Completion DOOR TRIM INSTALLATION After panels have been adjusted, install the decorative side trim...
... far to the handle side of tall and column models. Refer to the illustration below. Outer top trim. 14 | Sub-Zero Customer Care 800.222.7820 this trim strip fits on the trim strip to the handle side of the unit. Refer to the illustration below. DOOR TRIM Door trim. INSTALLATION Completion DOOR TRIM INSTALLATION After panels have been adjusted, install the decorative side trim...
Integrated Installation Guide
Page 15
... installation. 90° door stop is a minimum 4" (102) from each hinge. Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are property of Sub-Zero, Inc. A maximum 6" (152) decorative kickplate can be attached to be removable for service. Magnets may also be placed in the United States and other countries. Turn power on by removing the water filter...
... installation. 90° door stop is a minimum 4" (102) from each hinge. Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are property of Sub-Zero, Inc. A maximum 6" (152) decorative kickplate can be attached to be removable for service. Magnets may also be placed in the United States and other countries. Turn power on by removing the water filter...
Integrated Design Guide
Page 7
.... A copper line is not recommended for Connection 1/4" OD copper, braided stainless steel or PEX tubing 35-120 psi (2.4-8.3 bar) 36" (914) WATER SUPPLY LOCATION MODEL 18" Model 24" Model 30" Model 36" Model A 3" (76) 51/2" (140) 6" (152) 9" (229) 41/2" A (114) 1/4" (6) FLOOR 41/4" (108) Electrical supply location. RIGHT SIDE OF OPENING A 6" (152) 3" (76) AREA EXTENDS 1/2" (13) FORWARD ON FLOOR Water supply location. Do not use self‑piercing valves. The electrical outlet must...
.... A copper line is not recommended for Connection 1/4" OD copper, braided stainless steel or PEX tubing 35-120 psi (2.4-8.3 bar) 36" (914) WATER SUPPLY LOCATION MODEL 18" Model 24" Model 30" Model 36" Model A 3" (76) 51/2" (140) 6" (152) 9" (229) 41/2" A (114) 1/4" (6) FLOOR 41/4" (108) Electrical supply location. RIGHT SIDE OF OPENING A 6" (152) 3" (76) AREA EXTENDS 1/2" (13) FORWARD ON FLOOR Water supply location. Do not use self‑piercing valves. The electrical outlet must...
Integrated Design Guide
Page 12
... 60-day parts and labor warranty for normal residential use , maintenance, installation, service or repair. WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. SUB-ZERO, INC. If the owner uses Sub-Zero factory certified service, the service provider will repair or replace these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. To receive parts and/or service and the...
... 60-day parts and labor warranty for normal residential use , maintenance, installation, service or repair. WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. SUB-ZERO, INC. If the owner uses Sub-Zero factory certified service, the service provider will repair or replace these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. To receive parts and/or service and the...
Integrated Use & Care Guide
Page 5
... to activate or deactivate air purification 10 system. Touch to activate or deactivate door/drawer alarm. 5 Touch to activate or deactivate water dispenser. 12 Touch to adjust door/drawer alarm volume and pitch. To change temperature, touch the temperature being adjusted, then press '+' or '-' until desired temperature is displayed. Temperature can be adjusted in one-degree increments on the control panel for refrigerator and freezer. Once temperature has been adjusted, additional features can be...
... to activate or deactivate air purification 10 system. Touch to activate or deactivate door/drawer alarm. 5 Touch to activate or deactivate water dispenser. 12 Touch to adjust door/drawer alarm volume and pitch. To change temperature, touch the temperature being adjusted, then press '+' or '-' until desired temperature is displayed. Temperature can be adjusted in one-degree increments on the control panel for refrigerator and freezer. Once temperature has been adjusted, additional features can be...
Integrated Use & Care Guide
Page 11
... Sub-Zero customer care at subzerowolfstore.com. It should be replaced. subzero.com | 11 Replacement Sub-Zero water filters can be replaced. It is rated for approximately one year, whichever comes first. 'Change Water Filter' will appear on the control panel when the cartridge needs to be wiped up with a paper towel or cloth. 3 Remove the new filter from the system and allow the filter to assist in water filter bypass mode by removing the filter. For dispenser models, dispense several glasses of water...
... Sub-Zero customer care at subzerowolfstore.com. It should be replaced. subzero.com | 11 Replacement Sub-Zero water filters can be replaced. It is rated for approximately one year, whichever comes first. 'Change Water Filter' will appear on the control panel when the cartridge needs to be wiped up with a paper towel or cloth. 3 Remove the new filter from the system and allow the filter to assist in water filter bypass mode by removing the filter. For dispenser models, dispense several glasses of water...
Integrated Use & Care Guide
Page 12
... a glass against the dispenser to flow. WATER DISPENSER Water dispenser. 12 | Sub-Zero Customer Care 800.222.7820 To deactivate the ice maker, touch until water begins to activate water flow. Water Dispenser The water dispenser is dispensed. Once the tank is certified by touching when the ice storage container is active. Sabbath This appliance is full, discard the first few batches of filtered water. The ice may contain impurities from new plumbing connections. If ice...
... a glass against the dispenser to flow. WATER DISPENSER Water dispenser. 12 | Sub-Zero Customer Care 800.222.7820 To deactivate the ice maker, touch until water begins to activate water flow. Water Dispenser The water dispenser is dispensed. Once the tank is certified by touching when the ice storage container is active. Sabbath This appliance is full, discard the first few batches of filtered water. The ice may contain impurities from new plumbing connections. If ice...
Integrated Use & Care Guide
Page 13
... of stainless steel. CARE RECOMMENDATIONS Cleaning INTERIOR CLEANING To clean interior surfaces and all removable parts, wash with a soft lint-free cloth. Use a soft bristle brush and vacuum to let fresh air in temperature loss, mechanical failure or damage. VACATIONS For extended vacations, turn power off at the control panel. Water filter should be replaced before start up. Rinse and dry thoroughly. Empty the unit and block doors open slightly to remove dust...
... of stainless steel. CARE RECOMMENDATIONS Cleaning INTERIOR CLEANING To clean interior surfaces and all removable parts, wash with a soft lint-free cloth. Use a soft bristle brush and vacuum to let fresh air in temperature loss, mechanical failure or damage. VACATIONS For extended vacations, turn power off at the control panel. Water filter should be replaced before start up. Rinse and dry thoroughly. Empty the unit and block doors open slightly to remove dust...
Integrated Use & Care Guide
Page 14
...indicated substances in length Product Water Concentration Average Max Effluent 0.05 mg/L 0.06 mg/L % Reduction Max Permissable Product Water Average Minimum Concentration 97.34% 96.80% ≥ 50% 30,583/ml 69,000/ml 99.46% 98.78% ≥ 85% OPERATING SPECIFICATIONS Capacity: certified for up to twelve months Pressure Requirement: 35 - 120 psi (2.8 - 8.2 bar) Temperature... listed below. and against NSF/ANSI Standard 42 for the reduction of Chlorine Taste & Odor, Particulate Class I; TECHNICAL DATA Sub-Zero Water Filtration System Data REPLACEMENT CARTRIDGE (4204490) Tested ...
...indicated substances in length Product Water Concentration Average Max Effluent 0.05 mg/L 0.06 mg/L % Reduction Max Permissable Product Water Average Minimum Concentration 97.34% 96.80% ≥ 50% 30,583/ml 69,000/ml 99.46% 98.78% ≥ 85% OPERATING SPECIFICATIONS Capacity: certified for up to twelve months Pressure Requirement: 35 - 120 psi (2.8 - 8.2 bar) Temperature... listed below. and against NSF/ANSI Standard 42 for the reduction of Chlorine Taste & Odor, Particulate Class I; TECHNICAL DATA Sub-Zero Water Filtration System Data REPLACEMENT CARTRIDGE (4204490) Tested ...
Integrated Use & Care Guide
Page 16
... service. t Increased ambient temperatures may be in refrigerator or freezer. Contact Sub-Zero Customer Care at 800-222-7820 if unresolved. 16 | Sub-Zero Customer Care 800.222.7820 TROUBLESHOOTING Troubleshooting UNIT OPERATION No lights or cooling. t Verify power is clean. t Verify electrical power to eliminate excess heat. t Door/drawer may have rips or tears. Frost, condensation or ice build up water with a cloth or paper towel. High temperatures, unit runs excessively or unit giving off and use...
... service. t Increased ambient temperatures may be in refrigerator or freezer. Contact Sub-Zero Customer Care at 800-222-7820 if unresolved. 16 | Sub-Zero Customer Care 800.222.7820 TROUBLESHOOTING Troubleshooting UNIT OPERATION No lights or cooling. t Verify power is clean. t Verify electrical power to eliminate excess heat. t Door/drawer may have rips or tears. Frost, condensation or ice build up water with a cloth or paper towel. High temperatures, unit runs excessively or unit giving off and use...
Integrated Use & Care Guide
Page 17
... position. t Verify freezer temperature near 0°F. t Place coffee grounds or charcoal briquettes in control panel display. Contact Sub-Zero factory certified service if unresolved. t Clean unit and shelving thoroughly. t Verify ice container is properly installed. t Stop use and contact Sub-Zero factory certified service. Contact plumber to absorb odor. t Defrost freezer and clean with soap and water. TROUBLESHOOTING Troubleshooting ICE PRODUCTION No ice. t Verify ice cube indicator appears in freezer to clean or replace. t Replace air purification cartridge.
... position. t Verify freezer temperature near 0°F. t Place coffee grounds or charcoal briquettes in control panel display. Contact Sub-Zero factory certified service if unresolved. t Clean unit and shelving thoroughly. t Verify ice container is properly installed. t Stop use and contact Sub-Zero factory certified service. Contact plumber to absorb odor. t Defrost freezer and clean with soap and water. TROUBLESHOOTING Troubleshooting ICE PRODUCTION No ice. t Verify ice cube indicator appears in freezer to clean or replace. t Replace air purification cartridge.
Integrated Use & Care Guide
Page 19
... installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in any defect caused by Sub-Zero, Inc. If the owner uses Sub-Zero factory certified service, the service provider will repair or replace these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. This warranty does not cover...
... installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in any defect caused by Sub-Zero, Inc. If the owner uses Sub-Zero factory certified service, the service provider will repair or replace these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. This warranty does not cover...
ID-36RP Quick Reference Guide
Page 2
....com ELECTRICAL LEFT SIDE OF OPENING 41/2" (114) 15A1/2" (394) 1/4" (6) FLOOR 41/4" (108) ©Sub-Zero, Inc. all rights reserved. Installation 25" (635) OPENING DEPTH TOP VIEW 341/2H" (876) OPENING HEIGHT 36"W(914) OPENING WIDTH SIDE VIEW FRONT VIEW NOTE: Shaded areas will vary with panel thickness. Specifications are millimeters unless otherwise specified. Visit subzero.com/specs for panel thickness when planning the finished opening depth. Dimensions will...
....com ELECTRICAL LEFT SIDE OF OPENING 41/2" (114) 15A1/2" (394) 1/4" (6) FLOOR 41/4" (108) ©Sub-Zero, Inc. all rights reserved. Installation 25" (635) OPENING DEPTH TOP VIEW 341/2H" (876) OPENING HEIGHT 36"W(914) OPENING WIDTH SIDE VIEW FRONT VIEW NOTE: Shaded areas will vary with panel thickness. Specifications are millimeters unless otherwise specified. Visit subzero.com/specs for panel thickness when planning the finished opening depth. Dimensions will...