Smeg KSE912XU Support and Manuals
Get Help and Manuals for this Smeg item
This item is in your list!
View All Support Options Below
Free Smeg KSE912XU manuals!
Problems with Smeg KSE912XU?
Ask a Question
Free Smeg KSE912XU manuals!
Problems with Smeg KSE912XU?
Ask a Question
Popular Smeg KSE912XU Manual Pages
Instruction Manual - Page 3
...rangehood requires at high settings. Make sure there...INSTALLED MUST BE SEALED. MOBILE HOME INSTALLATION.
Do not cut , then a supporting frame must be constructed.
READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING... 24 CFR, Part 3280 (formerly ...INSTRUCTIONS
The Installer must be revised. Four wire power supply must be used and the appliance wiring must leave these instructions...
Instruction Manual - Page 4
...WITH COPPER WIRE ONLY. A hole cut a 1 1/4" hole in the cable so the appliance can be moved if servicing is ever necessary. CAUTION: For General Ventilating Use Only. W A R N I ...appliance should be connected directly to the requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and ordinances.
A hole through metal must be sized per local codes...
Instruction Manual - Page 5
...FOLLOWING: Installation Work And Electrical Wiring Must Be Done By Qualified Person(s) In Accordance With All Applicable Codes And... Standards, Including Fire-Rated Construction.
EN
55 When cutting or drilling into wall or ceiling, do not damage electrical wiring and other materials, DO
NOT use for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code...
Instruction Manual - Page 6
...installation. • Check that the main voltage corresponds to that do not apply to your specific appliance. rect use : overheated oil can
burst into flames. • The hood should not be held liable for any maintenance work. • Clean and/or replace... AND SUGGESTIONS
The Instructions for Use apply to several versions of minimum diameter 6". INSTALLATION • The manufacturer...
Instruction Manual - Page 7
...Installation Components 7.2.1 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs (if supplied) 12a 6 Screws 3/16" x 1" 3/4 12c 6 Screws 1/8" x 3/8"
Q.ty Documentation 1 Instruction Manual...
10
2.1 2
8b 2.2
1
15 14.1
12a 7.2.1 11
12c 8a
11 12a
EN
77 DIMENSIONS and MAIN PARTS
Dimensions
2" 7/16 5" 1/8
3" 1/2
Min. 35"...
Instruction Manual - Page 8
...4"9/16 12a
12"5/8
24"
Wall marking: • Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the
center of the area in which the hood will be installed. • Draw a horizontal line at 24" above the horizontal reference line. •... of the holes in the hood body fixing holes, leaving a gap of 3/16 "
between the wall and the head of the up-
Instruction Manual - Page 9
... connection 15 onto the hood body outlet. • Insert the connection extension pieces laterally 14.1 in position using sufficient pipe clamps (not sup-
If necessary, install a wood support behind the dry wall, flush mounted between 2 studs.
tion 15. • Make sure that the activated charcoal filters have been inserted.
15
14.1
EN...
Instruction Manual - Page 10
...-
At-
tween the upper flue and the wall, making sure that they are
well seated.
• Fix the lower part laterally to the hood body using the 4 screws 12c sup-
2.1
plied.
2
8b
Lower exhaust chimney
2.2
• ...from the Field Wiring Compartment with a twist-on type wire connector.
• Replace the cover. screw
Connect the Power Supply Cable to the green screw
provided.
Instruction Manual - Page 11
... ma- intensive speed from any previously selected The spot down at the right side motor to replaced. where vapours and odours need to jam the keyboard when, for a complete elimination of the... This function is on.
the intensive speed or the Delay-function this key it is possible to set the The suction speed and the remaining time be- grease filters have to a suction speed at...
Instruction Manual - Page 12
... appears on the display or in any case every 2 months, or even more frequently in the dishwasher. Pay attention not to be washed in case of particularly intensive use of the filter remains outside.... EN
112
2
Alarm reset • Press the G-key for at a time, supporting them with one
hand and turning the safety knobs (pull and turn). • Wash the filters. ...
Instruction Manual - Page 13
... same type, making sure that the two pins are properly inserted in the lamp holder socket holes. • Replace the Support, fixing it out of from the Hood. • Extract the lamp from the Support. • Replace with the two screws removed as indicated in -
tion alarm on the display appears: • 2 flashings on...
Smeg KSE912XU Reviews
Do you have an experience with the Smeg KSE912XU that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Smeg yet.
Earn 750 points for your review!