Singer ProFinish 14CG754 Serger Support and Manuals
Get Help and Manuals for this Singer item
View All Support Options Below
Free Singer ProFinish 14CG754 Serger manuals!
Problems with Singer ProFinish 14CG754 Serger?
Ask a Question
Free Singer ProFinish 14CG754 Serger manuals!
Problems with Singer ProFinish 14CG754 Serger?
Ask a Question
Singer ProFinish 14CG754 Serger Videos
SINGER ProFinish Serger Sewing Machine [;:] SINGER ProFinish 14CG754 Serger Sewing Machine Review!+.
Duration: 4:55
Total Views: 163
Duration: 4:55
Total Views: 163
Popular Singer ProFinish 14CG754 Serger Manual Pages
Instruction Manual 15 - Page 1
14SH744/14CG744 (2.3.4 THREAD OVERLOCK MACHINE) 14SH754/14CG754 (2.3. 4 THREAD OVERLOCK MACHINE WITH DIFFERENTIAL FEED)
Operator's Guide
SINGER
SINGER
Instruction Manual 15 - Page 2
... use and optimum service. Then familiarize yourself with the machine by following the operator's guide page by authorized dealer.
®Singer is damaged, it must be replaced by young children or infirm persons without notification or obligation. IMPORTANT SAFETY INSTRUCTIONS
Ak
* If the supply cord is a registered trademark of The Singer Company Limited or its service agent or...
Instruction Manual 15 - Page 3
...; When sewing, keep fingers away from the accumulation of it has been dropped or damaged, or dropped into any other user servicing adjustments mentioned in the Operator's Guide.
• To disconnect, turn all moving parts. Keep ventilation openings of the machine and foot controller free from all controls to the nearest authorized dealer or...
Instruction Manual 15 - Page 7
...•0
3.0
0.5
7.0 looper
Four-Thread Ultra-
6 Stretch Mock Safety Stitch
ire
(514)
2.5
2.0
2.5
2.0
Upper looper
35
The thread tension becomes tighter as throughout the operator's manual are turned to suit the fabric and.... Adjust thread tensions to higher numbers. HANDY REFERENCE CHART
Stitch Type
Needle Positions
Tension Dial: Numbers shown are average settings on this ...
Instruction Manual 15 - Page 8
... the machine.
• In an emergency, standard Singer needle #2020 may occur. Sizes available
Singer needle #2022
80/11 90/14
7
NEEDLE INFORMATION
• Singer needle #2022 size 90/14 is readjusted, skipping of the stitches may be used. ACCESSORIES
I
Accessories are contained in the accessory case in the cloth plate.
1 Needle set 2 Screw driver (small...
Instruction Manual 15 - Page 9
PRINCIPAL PARTS
1 Thread guides and holder 2 Handle 3 Left needle thread tension dial (blue) 4 Right needle thread tension dial (green) 5 Upper looper thread tension dial (orange) 6 Lower looper thread tension dial (yellow) 7 Throat plate 8 Cloth plate 9 Looper cover 10 Power & light switch 11 Stitch length dial 12 Hand wheel 13 Spool stand 14 Spool ...
Instruction Manual 15 - Page 11
...10 SINGER
• Center the thread guides above the spool pins.
• Place thread over...CANADA ONLY)
This appliance has a polarized plug (one way. A Warning:
* Be sure that the electrical voltage of electric shock, this plug is threaded, straighten the threads to place anything on top of it on the floor. PREPARATION FOR THREADING
Setting Up the Thread Guide Holder
• This machine...
Instruction Manual 15 - Page 14
... looper area of the throat plate.
I
• Thread the hole in threading the looper.
• Pull about 10cm (4 inches) of thread through the looper and place to back 8. Note: Use of tweezers provided in the accessory set to aid in the upper looper from front to the back of the machine following the orange color coded thread guides ( 4 - 7 ).
Instruction Manual 15 - Page 16
... of the machine following the yellow color coded thread guides 4 - 7 . Note : Use the tweezers provided in the accessory set to aid in threading the looper.
• Grasp the thread with the tweezers 4 cm (1-1/2 inches) from thread guide 7.
• Place the thread with the point of the tweezers slightly under and to the left of threading guide 8.
• Pull the thread up and into thread guide...
Instruction Manual 15 - Page 19
... under thread guide 2 . •••
• While holding thread with finger, pass it is properly located in between the tension discs and pull thread down to the front through the thread guide 1 . 4) Threading the Left Needle (Blue)
• Thread the left needle as indicated 1 - 7.
• Pass thread from back to make certain it between the tension discs 3.
18
SINGER...
Instruction Manual 15 - Page 21
... threads through the machine one at a time. • If threads do not pull easily, check for tangles on stand. • Tie new thread and old thread ends together. • Clip thread tails to previous settings.
20
SINGER 12. HOW TO CHANGE THREADS / TIE ON METHOD
• To change thread type or color, clip thread near the spool.
• Place new thread on
thread guides...
Instruction Manual 15 - Page 37
... SEW A ROLLED HEM s.
• This machine can sew four types of thread combinations can be sewn.
• Needle: Singer Needle #2022 size 80/11 or 90/14
• Thread: A variety of rolled hems.
• Rolled hemming is not suited for rolled hemming.
•
•
AI"
►
2
36 etc. 23.
Machine Set Up
• Remove the left...
Instruction Manual 15 - Page 49
... 12-19
30-38 20 49 21 22
47 47
9 20
9
48 Insert needle correctly. - Shorten stitch length. - TROUBLE SHOOTING CHART
Problem
Solution
Fabric does not feed well Needle breaks Thread breaks
Stitches skip
Irregular stitches Fabric puckers
Irregular trimming Fabric jams Machine does not operate
- Decrease presser foot pressure for tangled or caught...
Instruction Manual 15 - Page 50
RELATIONSHIP BETWEEN CLOTH, THREAD AND NEEDLE
Type of Thread
Cotton: #100 Silk: #100 Spun: #80 - #90 Tetron: #80 - #100
Needle Singer Cat. No. 2022 is furnished with the machine however.
#14 #11 #11, #14 #11, #14
It is recommended that you select your needle in accordance with the material you are sewing. 49 27.
...
Instruction Manual 15 - Page 51
SPECIFICATION
Item
Specification
Sewing speed Stitch length (feed amount) Differential feed ratio Overedge stitch width
Needle bar stroke Presser foot rise Needle
Model Number of threads Machine dimensions (mm)
Width Depth Height
Weight (Kg)
1,300 spm maximum 1 - 4mm (standard: rolled hemming F - 2, ordinary overedge 3.0) 1:0.7 - 1:2 (with differential feed machine) Rolled hemming 1.5mm, ...
Singer ProFinish 14CG754 Serger Reviews
We have not received any reviews for Singer yet.