Product Manual
Page 6
commands 30 iv Medalist 4342, 3232, 2122, 1722 and 1012 Product Manual 1.12.2 Electromagnetic Compatibility 15 1.12.3 FCC verification 15 2.0 Drive mounting and configuration 17 2.1 Handling and static-discharge precautions 17 2.2 Jumper settings 17 2.2.1 Master/slave configuration 17 2.2.2 Alternate capacity jumper 17 2.3 Drive mounting 18 3.0 ATA interface 21 3.1 ATA interface signals and connector pins 21 3.1.1 AT bus...
commands 30 iv Medalist 4342, 3232, 2122, 1722 and 1012 Product Manual 1.12.2 Electromagnetic Compatibility 15 1.12.3 FCC verification 15 2.0 Drive mounting and configuration 17 2.1 Handling and static-discharge precautions 17 2.2 Jumper settings 17 2.2.1 Master/slave configuration 17 2.2.2 Alternate capacity jumper 17 2.3 Drive mounting 18 3.0 ATA interface 21 3.1 ATA interface signals and connector pins 21 3.1.1 AT bus...
Product Manual
Page 25
... ST33232A, these drives include a capacity-limiting jumper, which sets the drive's default translation geometry to 2.1 Gbytes, unless third-party software is preferred. Medalist 4342, 3232, 2122, 1722 and 1012 Product Manual 17 2.0 Drive mounting and configuration 2.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may "hang" if their BIOS detects a hard drive that has more...
... ST33232A, these drives include a capacity-limiting jumper, which sets the drive's default translation geometry to 2.1 Gbytes, unless third-party software is preferred. Medalist 4342, 3232, 2122, 1722 and 1012 Product Manual 17 2.0 Drive mounting and configuration 2.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may "hang" if their BIOS detects a hard drive that has more...
Product Manual
Page 26
... clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for drive mounting dimensions. 18 Medalist 4342, 3232, 2122, 1722 and 1012 Product Manual 3 4 1 2 3 1 Alternate capacity jumper 42 Full capacity (as shipped) ATA interface pin 1 connector 4-pin power connector Master/slave jumper settings 2 46 135 Limit capacity to boot because it cannot address...
... clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for drive mounting dimensions. 18 Medalist 4342, 3232, 2122, 1722 and 1012 Product Manual 3 4 1 2 3 1 Alternate capacity jumper 42 Full capacity (as shipped) ATA interface pin 1 connector 4-pin power connector Master/slave jumper settings 2 46 135 Limit capacity to boot because it cannot address...
Product Manual
Page 33
...alternate capacity jumper is installed on the ST34342A or the ST33232A, the drive capacity is organized as a single 512-byte block of logical heads: 15 (ST34342A) 3 16 (ST33232A) (ST32122A) (ST31722A) (ST31012A) 4 Retired continued 0000H 000FH (ST34342A) 0010H (ST33232A) (ST32122A) (...ST31722A) (ST31012A) 0000H The data is reduced in the Draft ATA-4 Standard. 3.2.2 Identify Drive command The Identify Drive command (command code ECH) transfers information about the drive to the host following commands contain drive-specific features that may not be set to ...
...alternate capacity jumper is installed on the ST34342A or the ST33232A, the drive capacity is organized as a single 512-byte block of logical heads: 15 (ST34342A) 3 16 (ST33232A) (ST32122A) (ST31722A) (ST31012A) 4 Retired continued 0000H 000FH (ST34342A) 0010H (ST33232A) (ST32122A) (...ST31722A) (ST31012A) 0000H The data is reduced in the Draft ATA-4 Standard. 3.2.2 Identify Drive command The Identify Drive command (command code ECH) transfers information about the drive to the host following commands contain drive-specific features that may not be set to ...