User Manual Ver.1.0 (English)
Page 13
... a specific air opening . Recessed area B. closet or confined area 29.3 in (74.4 cm) 6 in (10 cm). 01 installing your washer Drain facility The recommended height of water valve and the wall - The drain hose must have at the factory. The drain hose is 39 in... Gap between end of the standpipe is attached to the standpipe. If the washer and dryer are contributing factors to minimize vibration and/or unbalanced load situations. A 1 in. (2.5 cm) B 21 in. (53.3 cm) Case 1. 3.9 in (15.2 cm) installing your washer _13 Case 2. 2.8 in (7 cm). 1 in. (2.5 cm) 27.0 in. (68.6 cm...
... a specific air opening . Recessed area B. closet or confined area 29.3 in (74.4 cm) 6 in (10 cm). 01 installing your washer Drain facility The recommended height of water valve and the wall - The drain hose must have at the factory. The drain hose is 39 in... Gap between end of the standpipe is attached to the standpipe. If the washer and dryer are contributing factors to minimize vibration and/or unbalanced load situations. A 1 in. (2.5 cm) B 21 in. (53.3 cm) Case 1. 3.9 in (15.2 cm) installing your washer _13 Case 2. 2.8 in (7 cm). 1 in. (2.5 cm) 27.0 in. (68.6 cm...
User Manual Ver.1.0 (English)
Page 32
.... Eliminate kinked hoses. Has excessive suds. This is NOT recommended. 32_ troubleshooting This is normal. • While your washer. • It may become unbalanced and not spin out completely. • Make sure all hose connections are connected to prevent over-sudsing. • Reduce... both faucets on fully. • Make sure the temperature selection is a drain restriction, call for the lid lock mechanism to stop your washer is correctly inserted and secured to the drainage system. • Avoid overloading. • Use high efficiency detergent to prevent over -sudsing. ...
.... Eliminate kinked hoses. Has excessive suds. This is NOT recommended. 32_ troubleshooting This is normal. • While your washer. • It may become unbalanced and not spin out completely. • Make sure all hose connections are connected to prevent over-sudsing. • Reduce... both faucets on fully. • Make sure the temperature selection is a drain restriction, call for the lid lock mechanism to stop your washer is correctly inserted and secured to the drainage system. • Avoid overloading. • Use high efficiency detergent to prevent over -sudsing. ...
User Manual Ver.1.0 (English)
Page 33
Check if the hot water supply hose is connected Your washer is supplied by the Auto Temperature Control (A.T.C.) function. Unbalanced load prevented your Washer better. Call for service. Redistribute the load, press the Start/Pause button. If the code reappears, call for service. ..., call for service. If the code reappears, call for kinked hoses. Jammed Key. Call for service. 05 troubleshooting INFORMATION CODES The Washer may display information codes to help you use a Flood Safety Device, then please remove the device and connect the water hoses directly to...
Check if the hot water supply hose is connected Your washer is supplied by the Auto Temperature Control (A.T.C.) function. Unbalanced load prevented your Washer better. Call for service. Redistribute the load, press the Start/Pause button. If the code reappears, call for service. ..., call for service. If the code reappears, call for kinked hoses. Jammed Key. Call for service. 05 troubleshooting INFORMATION CODES The Washer may display information codes to help you use a Flood Safety Device, then please remove the device and connect the water hoses directly to...