Ryobi P5453 Support and Manuals
Get Help and Manuals for this Ryobi item
Popular Ryobi P5453 Manual Pages
Operation Manual - Page 3
...SERVICE
Have your power tool serviced by poorly maintained power tools.
Keep cutting tools sharp and clean. Follow instructions in a hazardous situation. Use of unauthorized parts or failure to follow Maintenance instructions... and off. Many accidents are caused by a qualified repair person using only identical replacement parts. BATTERY TOOL USE AND CARE
Recharge only ...
Operation Manual - Page 5
...and head protection when operating this unit.
Keep all parts of your body away from the falling tree. A chain saw... when using the chain saw who has not received adequate instructions in its proper use your finger on the switch trigger.... Stop the chain saw before setting it is not contacting any combination of these reactions may push the guide bar rapidly back towards the ...
Operation Manual - Page 6
... a bow guide or use chain saw should be properly repaired or replaced by wiping ...manual.
All chain saw service, other conditions that may affect its operation. Chain saw if switch does not turn after the switch trigger has been released, have to be stored in use.
Never use water or any liquids to prevent rotational kickback.
6 -
Remove any buildup of parts...
Operation Manual - Page 8
...B175.1. As saw in this operator's manual.
Save these instructions also.
8 -
When making a replacement, be sure to instruct others who may use replacement chain that has met the kickback ...kickback saw chain is made. Thus, the operator must be used.
English GUIDE BARS
Generally, guide bars with small radius tips have somewhat lower kickback potentials. specified in ...
Operation Manual - Page 11
...requirements when used with specific chain saws. It may be provided on the end of the guide bar to reduce kickback ...an electrical power circuit to the motor of the switch until manually actuated. SAFE-T-TIP™ Anti-Kickback Nose Guard An attachment ... The toothed part that supports and guides the saw chain.
This handle is supported by the motor and is for the right hand. Guide Bar A...
Operation Manual - Page 12
...SAFE-T-TIP™
BATTERY PORT
GUIDE BAR
Fig. 4
12 - Before use and has some limitations as a knowledge of this operator's manual as well as to what... it can cut.
Chain Speed 16 f/s (5 m/s) NOTE: This saw was designed for occasional light
duty use of the project you are attempting. KNOW YOUR PRUNING CHAIN SAW
See Figure 4. FEATURES
PRODUCT SPECIFICATIONS...
Operation Manual - Page 14
...the length of the guide bar.
WARNING:
...replaced.
Performing these cuts. WARNING:
Always wear eye protection with this product until all missing or damaged parts are assembling parts...service center for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. The use of this product for the following purposes: Basic limbing, felling, and woodcutting
TO INSTALL...
Operation Manual - Page 15
...limbing and pruning type cutting up to 6 in diameter only.
15 - For complete charging instructions, see the operator's manuals for continued operation.
WARNING:
Make sure the latches on battery pack with groove in contact ...pack could result in place properly. OPERATION
To install:
NOTICE:
When placing battery pack in your chain saw, be automatically reset to the lock position....
Operation Manual - Page 16
... line.
Always
keep your left -handed (cross-handed) grip, or any part of your body to be in this manual for appropriate safety equipment. Wear non-slip gloves for maximum grip ... operation of control. The fingers should encircle the handle and the thumb is to Important Safety Instructions earlier in the chain line while operating a saw ). English
Fig. 12 Never allow any...
Operation Manual - Page 17
...you begin a major sawing operation. Support log on a saw horse or cradle.
Always cut with both feet.
Leave the larger support limbs under the tree to
keep the tree ...the following technique to use this chain saw who has not read this Operator's Manual or received adequate instructions for the safe and proper use the proper cutting stance described in loss of ...
Operation Manual - Page 18
... is difficult to control against the main member so the bark will grow back to seal the wound.
2
3
1
4
CUT LIMBS ONE AT A TIME AND LEAVE SUPPORT LIMBS UNDER TREE UNTIL LOG IS CUT
Fig. 13
LOAD SECOND CUT
FIRST CUT 1/3 DIAMETER
FINISHING CUT
SPRINGPOLE
Fig. 14
WARNING:
If the limbs to...
Operation Manual - Page 19
... injury. CHAIN COVER
Fig. 16
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. REPLACING BAR AND CHAIN
See Figures 16 - 20. SPROCKET
CHAIN COVER SCREW
CHAIN
BAR...this product until all the safety instructions in possible serious injury. Please contact customer service or an authorized service center for damaged, missing, or loose parts such as screws, nuts, bolts...
Operation Manual - Page 22
... the risk of wear or damage are present in the areas indicated, have the drive sprocket replaced by mud or sand on the saw to one side.
HOW TO SHARPEN THE CUTTERS
See ...on the wood, have been abraded by a RYOBI Service dealer. BAR AND CHAIN LUBRICATION
Using a quality bar oil, oil the bar and chain manually, as needed.
MAINTENANCE
CHAIN MAINTENANCE
See Figures 23 - 24...
Operation Manual - Page 23
...
See Figure 28.
CORRECT - 80° Produced automatically if correct diameter file is used in this manual. Refer to the other side and file the right hand cutters in . File all of your filing at the...
RAKER CLEARANCE .025 in one direction. File holders are marked with guide marks to align file properly to replace or repair damaged chain can result in severe engine damage.
Operation Manual - Page 26
Guide Bar Part Number 316670001
Chain Part Number 682502001
Drive Links 33
TROUBLESHOOTING
PROBLEM
Bar and chain running hot and smoking.
Motor runs, but chain is not rotating.
This product has a Three-year Limited Warranty for personal, family, or household use (90 days for damage. Length of Bar 8 in this manual. Check guide bar and chain for...
Ryobi P5453 Reviews
We have not received any reviews for Ryobi yet.