Ryobi A25RT03 Support and Manuals
Get Help and Manuals for this Ryobi item
View All Support Options Below
Free Ryobi A25RT03 manuals!
Problems with Ryobi A25RT03?
Ask a Question
Free Ryobi A25RT03 manuals!
Problems with Ryobi A25RT03?
Ask a Question
Popular Ryobi A25RT03 Manual Pages
Operation Manual - Page 2
... if the cutting operation is unintentionally contacted.
CHECK DAMAGED PARTS. Wear hearing protection during extended periods of checking to avoid risk of the blade, cutter, or sanding spindle only.
PROTECT YOUR LUNGS. Carefully read the router table operator's manual and the manual for recommended accessories. Do not force the tool or attachment to...
Operation Manual - Page 3
... avoid risk.
SAVE THESE INSTRUCTIONS. Have defective switches replaced by an authorized service center to a power source.
DO NOT USE AWKWARD HAND POSITIONS.
FIRMLY CLAMP OR BOLT THE ROUTER TABLE TO A WORK SURFACE so that are not listed may use only identical replacement parts. Do not reach underneath the table or in this rule will...
Operation Manual - Page 5
... the motor to support two or three ...precision built electric motor.
If repair or replacement of the electric cord or ... that have the proper outlet installed by a qualified electrician. Use...router you are working with all local codes and ordinances.
Wire that accept the product's plug.
Never use product with a qualified electrician or service personnel if the grounding instructions...
Operation Manual - Page 6
... lbs.
RESET BUTTON The router table switch is used with all operating features and safety rules.
English Fence Length 28 in .
It also has pre-drilled countersunk holes that protects the electronic components of routers. Only use the starting pin.
6 - FEATHERBOARD
The featherboard allows for mitered routing and to support and guide the work. FENCE...
Operation Manual - Page 8
... operated the product. n Carefully remove the product and any parts on this tool until the parts are damaged or missing do so could result in serious personal injury.
8 - WARNING:
Do not use with damaged or missing parts could result in place before using the router table. WARNING:
Do not connect to make sure no breakage...
Operation Manual - Page 9
... Knob Washer 2 U. Router Insert Plate Screws (5/16-18 x 3/4 in 3 H. Table Top 1 J. L. Miter Gauge 1 P. Featherboard Bolts 2 T. Fence Lock Knobs 2 R. Featherboard Lock Knobs 2 V. Table Leg 4 I 3 ...in 3 G. Under Table Guard 2 N. Featherboard 1 S. English ASSEMBLY
H C
A
I . Carriage Bolt 2 M. Hex Key 1 C. Under Table Guard Screw 6 E. Router Insert Plate Screws ...
Operation Manual - Page 10
... the screws and nuts from the switch
box. Place the router table upside down on a flat surface. Hold the switch box so that is already installed on the front underside of the table. ATTACHING THE UNDER TABLE GUARDS
See Figure 6.
Remove the table leg screws from the blister pack. Use these screws and nuts...
Operation Manual - Page 11
...of the three included sets of the router table. n Remove the throat plate.
n Remove the subbase plate from the blister pack. ASSEMBLY
NOTE: The table leg with the ...table. Insert the table leg screws through the holes and into the router table. PRE-DRILLING HOLES FOR THROUGH TABLE DEPTH ADJUSTMENT
See Figure 8. n Unplug the router table and/or the router.
Only the models...
Operation Manual - Page 14
... wh1 en you , place the miter gauge bar in the slot near the front of the router table throat opening. Remove the starting pin into place.
To remove, push throat plate out from the blister pack.
INSTALLING THE MITER GAUGE
See Figure 17. FENCE LOCK KNOB
MITER GAUGE BAR
3 2 1 0 1
Inch
SLOT
FEATHERBOARD...
Operation Manual - Page 15
... four bolts (not included, 1/4-20 recommended) and tighten securely with the holes in the router table leg. Tighten clamp securely. CLAMPING THE ROUTER TABLE TO A WORK BENCH
See Figure 19. or 2-1/2 in . n Unplug the router table and/or the router. Place the router table right side up on a sturdy work
surface; e.g., leg stand, workbench, counter top. ...
Operation Manual - Page 16
... make you are assembling parts, making adjustments, installing or removing cutters, cleaning, or when not in possible serious injury. The use this product. Failure to do so could cause serious personal injury.
APPLICATIONS
You may use of serious personal injury, never connect the table mounted router into and controlled by the router table switched outlet. To...
Operation Manual - Page 17
...CUTTERS
n Unplug the router table and/or the router. n Plug the router table power cord into either of the router table
switched outlets. n Always control the power to support the workpiece after the cut , never position the fence such that all router adjustments are using the router: n Read the entire operator's manual for the router and router
table. n Always plug the router into a power...
Operation Manual - Page 18
... .
3 2 1 0 1
Inch
ADJUSTING THE MITER GAUGE
See Figure 24. Inch
MITER GAUGE KNOB
n Consult the router operator's manual for adjusting the depth of the cutter. ADJUSTING DEPTH OF CUT
Consult the router operator's manual for proper cutter removal/installation procedure and replace cutter. n Rotate the miter gauge to the desired location. The fence enables you to widen...
Parts Diagram - Page 2
45 46 47 44
34
31 43 42 31
RYOBI ROUTER TABLE - MODEL NUMBER A25RT03
5
3 2
7 6
4
35 1
25
21
26
26
In1c0h127234 23
30
35
36
1
37
29 34
41
8
9
6
8
10
41 9
23 24 22
21 35
11
14 12 7
13 10 6
54
6
26
1 20 8
DIFREEECDTIIOn1Nc0h1234
28
35
1
28
29 34
29 30
12 14 15 12
16 12
17 18 19
53
34
40 39
38 55
34 31
33
32
31
48 57 49
52
6
50 56 58
51
2
Parts Diagram - Page 3
RYOBI ROUTER TABLE - MODEL NUMBER A25RT03
The model number will be found on a label attached to the switch box. KEY NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
PARTS LIST
PART NUMBER
DESCRIPTION
QTY
KEY PART NO. Key No. 26 1 089220105041 Under Table... in all correspondence regarding your ROUTER TABLE or when ordering replacement parts. Key Nos. 39-40 ...
Ryobi A25RT03 Reviews
We have not received any reviews for Ryobi yet.