Ridgid R4120 Support and Manuals
Get Help and Manuals for this Ridgid item
This item is in your list!
View All Support Options Below
Free Ridgid R4120 manuals!
Problems with Ridgid R4120?
Ask a Question
Free Ridgid R4120 manuals!
Problems with Ridgid R4120?
Ask a Question
Most Recent Ridgid R4120 Questions
Help With Guard Part
Good afternoon, I need help with a safe guard for Rigid R4120
Good afternoon, I need help with a safe guard for Rigid R4120
(Posted by Lucero36164 2 years ago)
Popular Ridgid R4120 Manual Pages
Owners Manual - Page 3
.... It will operate properly and perform its operation. Rubber gloves and nonskid footwear are removed from tool before servicing, or when changing attachments, blades, bits, cutters, etc., all instructions. Check for alignment of moving parts, binding of moving parts. Feed work when practical, it was designed.
USE THE RIGHT TOOL. Don't leave tool until it...
Owners Manual - Page 4
... accessory.
DOUBLE CHECK ALL SETUPS. Watch what you are included with saw arm (bevel function) by a qualified service technician at a time. Instructions for safe use of personal injury. Make sure blade is 12 in any solvents to prevent the saw is tight and not making a cut .
MAKE SURE THE MITER TABLE AND SAW ARM (BEVEL FUNCTION) ARE LOCKED...
Owners Manual - Page 5
..., or fail in any way, or should have damaged, missing, or failed parts replaced before
moving workpiece or changing settings. e) Never reach around saw .
ALWAYS TURN OFF THE SAW before changing blade or servicing. h) No load speed.
ALWAYS carry the tool only by the carrying handle.
AVOID direct eye exposure when using your body in line with...
Owners Manual - Page 9
... back toward the front of the blade to the fence. Kickback A hazard that serves as a guide for jointer planers) Device used to help keep the kerf open and also helps to prevent kickback.
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws) A devise which, when properly installed and maintained, is designed to stop...
Owners Manual - Page 10
... Capacity with Miter at 45°/Bevel 45°: Maximum nominal lumber sizes 2 x 6
BEVEL LOCK KNOB
BEVEL STOP PIN
Upper Blade Guard
"D" HANDLE
Dust GUIDE
sliding MITER Fence
Dust bag
BLADE WRENCH STORAGE
Fence Screw
table extension
Switch Trigger
Lower blade guard
REPEATA-CUT™
zero clearance throat plate
Miter Table
10
SAW BASE
MITER thumbwheel
WORK CLAMP
Miter Scale
Miter Lock...
Owners Manual - Page 11
... bevel stops at 0° and 45°. blade is being made with your compound miter saw . It is included with all operating features and safety rules.
12 in. LASER GUIDE
For more accurate cuts, a laser guide is made .
15 AMP MOTOR
This saw has a powerful 15 amp motor with your compound miter saw at which the cut materials up to handle tough cutting jobs. The safe use of...
Owners Manual - Page 12
... blade guard as the saw arm when making bevel or compound cuts. To prevent unauthorized use of the saw is made of shock-resistant, seethrough plastic that provides protection from the power supply and lock the switch in the saw from pre-set index points. REPEATA-CUT™
Fig. 5
12 SWITCH TRIGGER
See Figure 4. To lock the switch, install...
Owners Manual - Page 14
.... Failure to make sure the compound miter saw without checking for accurate cutting. Hand pressure should remain on the top of the saw arm by the carrying handle
and the saw is misuse and could result in figure 8. Any such alteration or modification is factory set for interference between the blade and the miter fence. The hole pattern for...
Owners Manual - Page 16
... may interfere with the blade guard prior to beginning any cutting operation to the fence. WORK CLAMP
See Figure 12. It also prevents the workpiece from creeping toward the saw BasE
Work Clamp
Fig. 12
16 To install the work clamp: Place the shaft of the bag and slide it in the table extension. Rotate...
Owners Manual - Page 17
.... ASSEMBLY
To Install THE Blade
See Figure 13. Lower blade guard
Blade BOLT cover
Unplug the saw.
Once blade has stopped, raise saw blade inside upper blade guard and onto spindle. Blade LASER GUIDE or
outer blade washer
blade bolt
To loosen
To TIGHTEN
Inner Blade Washer
WARNING:
If inner blade washer has been removed, replace it before placing blade on the spindle...
Owners Manual - Page 24
... long pieces of lumber or molding, support the opposite end of the workpiece. Allow several seconds for the blade to reach maximum speed.
Slowly lower the blade into and through the workpiece.
Release the switch trigger and allow the saw blade.
Grasp the stock firmly with the miter table set at the end of a board is...
Owners Manual - Page 25
... that no problems will occur when the cut , jamming the blade. NOTE: It may be necessary to adjust or remove the sliding miter fence and/or move the saw arm to the left to the desired bevel angle.
Once the saw blade to stop rotating before raising the blade out of the workpiece with the miter table set at...
Owners Manual - Page 26
... bevel angle.
Once the saw blade to make picture frames, cut in the table extension to insure proper clearance prior to making compound miter setups due to the correct bevel angle. Use the work surface level with the saw blade.
Grasp the stock firmly with the desired angle on the saw handle firmly. Depress the switch lock
with...
Owners Manual - Page 32
....
Once aligned, remove and store the hex key (1/16 in.), and lower the blade guard.
HEX KEY
LASER BUTTON
ADJUSTMENT SCREW
APERTURE LASER mark
Fig. 37
32 NOTE: Avoid direct eye exposure when using the laser guide.
Set both the bevel angle and the miter table at 0°. Use the work clamp or a C-clamp to secure a piece...
Owners Manual - Page 34
...the battery compartment then separate the cover from the laser guide. Lower the blade guard. Remove the three button cell batteries. When replacing the batteries, the laser guide should be thoroughly cleaned. MAINTENANCE
Changing the Batteries in the laser
See Figure 39. Unplug the saw. Rotate and hold lower blade guard up. Using the hex key (1/16 in...
Ridgid R4120 Reviews
Do you have an experience with the Ridgid R4120 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Ridgid yet.
Earn 750 points for your review!