Pyle PWD250 Support and Manuals
Get Help and Manuals for this Pyle item
Popular Pyle PWD250 Manual Pages
User Guide - Page 1
... associated with that may require additional parts and/or labor.
VEHICLE SECURITY SYSTEM
Optional Remote Start Module and 2-way Transmitter Instructions Included
SYSTEM MANUAL
STANDARD FEATURES Some of commands providing expanded... Cold Start Note: Some features may differ between models and between standard 1-way and LCD 2-way transmitters, but button functions remain the same as arm ...
User Guide - Page 2
...; The doors will unlock.* • The dome light will turn solid for the zone to close (depending on .*
¥ If the alarm was enabled during installation. If a door is armed. ARMING OPERATION To arm the system press transmitter button 1:
• The siren will chirp once. • The parking lights will flash...
User Guide - Page 3
...disarmed by using the emergency override feature. Enter the vehicle. • Because the system is not set. Press the Valet switch for 3 seconds.
• The siren will sound.
2. Press and hold...be programmed for ignition lock without brake. The Panic Feature will not start module is not installed and ignition locking is pressed with the ignition on /off : 1.
SILENT OPERATION MODE Press...
User Guide - Page 5
...programmed for PIN code override mode, the default code is on , and press valet switch 3 more times. OPTIONAL SECURE PIN CODE The system may be selected during installation or PIN code mode will not...anti-carjack after 60 seconds.
To activate anti-carjack protection: 1. Make sure the ignition is set to the button pressed.
6. The parking lights will begin flashing and the siren will begin ...
User Guide - Page 7
... timing must be able to remote start feature on , press lock button for installation in -gear starting . Press and hold the brake pedal. 2.
Selects between ... driver control, when the brake pedal is open. To resume driver control: 1. Turn on :
1. NOTE: Press and hold button 2 for level shift. 3. MANUAL TRANSMISSION MODE Manual Transmission Mode. Manual Transmission Quick Set...
User Guide - Page 13
... that shows +12V when the door is not connected, leave this wire disconnected and set Alarm Programmable Feature #3 to allow separate polarity inputs for negative lock systems. •...BLACK/RED jumper to either disarming the system (Dome Light) or after either button 2, 3 or 4 setting. Ground input (-). Connect the short BLACK wire to the same wire used with the optional remote start ...
User Guide - Page 14
... right parking light circuits; If the siren is not installed, the GRAY wire may be connected to a relay to... YELLOW WIRE - +12V Ignition input. Plug into 2-pin connector from the driver's position. 2-Pin Connector: Plug-in connector for second accessory. • ... to pulse the vehicle's horn. This wire may be optionally set to the main ignition wire that shows ground when the door is...
User Guide - Page 15
... ground when the wait-to-start or stop input when connected to an external device that is unavailable, leave the GRAY/BLACK wire disconnected, and set dip switch #2 to trigger the vehicle's defroster circuit and program Remote Start Programmable Feature #8 for Ignition 3 power supply. • BLACK/YELLOW WIRE (small) - For these...
User Guide - Page 16
...All Programming options are now set the Programming Features to indicate the button setting.
5. Ignition Lock/Unlock. Override Mode
No PIN Code PIN Code
7. Auxiliary Output Timing ...Programming • The siren will chirp either 1, 2, 3, or 4 times to factory default settings. 1. Enter Alarm or Remote Start Feature
program mode. 2. Auto Rearm.
After entering programming ...
User Guide - Page 17
... can be toggled on ; Allows the system to exit adjust mode.
17 Selects normal or PIN code mode for .8 seconds. Press button 1 to increase sensitivity or button 2 to open when the ...pressed. unlocks when ignition is turned off.The system will automatically disarm the system. Settings are set for Momentary,Timed, or Latched operation. Note: when the siren or horn mode is...
User Guide - Page 18
...9. Allows the vehicle to automatically start to level 2) the press lock button again. Manual Transmission Quick Set Mode Exit Sequence: Turn the ignition off (engine will remain running ) and exit vehicle...Ignition 1 and 2 relays. Installation and safe use in -gear starting and remains on for Factory Disarm output, the Yellow/Black wire pulses on a manual transmission vehicle is the sole...
User Guide - Page 19
...set dip switch #6 to On and be able to indicate presence of detecting the engine's run status using specially designed software that flashes to determine if the engine is cranking or if the engine is Gas Engine. ON= manual... module located next to the vehicle's tachometer
wire.This feature allows a faster installation, but may not be compatible with tach wire is reading a proper tach ...
User Guide - Page 20
..., Honda, BMW, Toyota, Nissan and others). General Motors Anti-theft Systems: Many late-model GM vehicles are equipped with anti-theft systems that use the proper bypass module for each ...resistance code generated when the key is equipped, then use either a resistor coded key or a passive transponder that system. Press the Lock Button on the shaft of these vehicles, you must be installed. ...
User Guide - Page 21
... closed configuration (default), the starter is only disabled when the alarm is powered up and is the recommended installation method. The normally open configuration is selected, Programmable Alarm Feature step 10 must be set to start the vehicle using the key, even if the alarm had been armed prior to start. In...
User Guide - Page 24
... plug input (+/-) Remote start input (-) Remote start output (-) 500mA Hood input (-) Progammable output (-) 500mA
Data-Link Cable (links alarm and start module)
DIP Switches - Default setting is OFF position (see Remote Start Dip Switches) Starter Test Button RPM Signal LED
64-72.50, 2/04 Rev. 1
24
Pyle PWD250 Reviews
We have not received any reviews for Pyle yet.