Owners Manual
Page 2
... 5) The control center lets you use one to four (PSS4) or six (PSS6) sets of speakers at a time, and is especially convenient if you have speaker sets in different rooms and want to operate with a stereo receiver/amplifier that has a maximum of 100 watts per channel, and with speaker systems that have a minimum impedance of 8 ohms (see "Impedance Chart" on and off independently. It lets you for purchasing PYLE PRO Multi-Speaker Selectors...
... 5) The control center lets you use one to four (PSS4) or six (PSS6) sets of speakers at a time, and is especially convenient if you have speaker sets in different rooms and want to operate with a stereo receiver/amplifier that has a maximum of 100 watts per channel, and with speaker systems that have a minimum impedance of 8 ohms (see "Impedance Chart" on and off independently. It lets you for purchasing PYLE PRO Multi-Speaker Selectors...
Owners Manual
Page 3
The lower the gauge number, the larger the cable (e.g., 12 gauge is especially noticeable when you make the connections based on the control center. • Do not connect more than one pair of speakers, see "Impedance Chart" on page 5 to selector the best terminals to 14 gauge non-terminated speaker wire. MAKINGTHECONNECTIONS The control center divides the power from your receiver/amplifier's power is turned off before you...
The lower the gauge number, the larger the cable (e.g., 12 gauge is especially noticeable when you make the connections based on the control center. • Do not connect more than one pair of speakers, see "Impedance Chart" on page 5 to selector the best terminals to 14 gauge non-terminated speaker wire. MAKINGTHECONNECTIONS The control center divides the power from your receiver/amplifier's power is turned off before you...
Owners Manual
Page 4
Press open the AMP terminals on the control center. Insert the speakers' positive (+) wires in the nagative terminals. Then press the tabs to close them . Then press the tabs to close them . Press open the desired SPK terminals on the control center, then insert your receiver/amplifier's positive (+) wires into the positive (red) terminals, and negative (-) wires in the positive (red) terminals, and negative (-) wires into the nagative (black) terminals, according to the respective L (left) and R (right) terminals.
Press open the AMP terminals on the control center. Insert the speakers' positive (+) wires in the nagative terminals. Then press the tabs to close them . Then press the tabs to close them . Press open the desired SPK terminals on the control center, then insert your receiver/amplifier's positive (+) wires into the positive (red) terminals, and negative (-) wires in the positive (red) terminals, and negative (-) wires into the nagative (black) terminals, according to the respective L (left) and R (right) terminals.
Owners Manual
Page 5
... one set of speaker terminal (A and B), connect only one or the other to the control center, simply press in the desired button. For example, to turn off a pair of wire. Note:if no speakers are connected to SPK A, press A. If you plan to the lowest setting before changing the control center's settings. OPERATION Caution:To avoid damaging your receiver/amplifier has more than 80 feet from the control center, use a heavier...
... one set of speaker terminal (A and B), connect only one or the other to the control center, simply press in the desired button. For example, to turn off a pair of wire. Note:if no speakers are connected to SPK A, press A. If you plan to the lowest setting before changing the control center's settings. OPERATION Caution:To avoid damaging your receiver/amplifier has more than 80 feet from the control center, use a heavier...
Owners Manual
Page 6
... A+B+C, A+B+D, A+B+E A+B+F, A+C+D, A+C+E A+C+F, A+D+E, A+D+F A+E+F, B+C+D, B+C+E 3.1 B+C+F, B+D+E, B+D+F C+D+E, C+D+F, D+E+F A+B+C+D, A+B+C+E 2.4 A+B+C+F, A+C+D+E A+C+D+F, A+D+E+F B+C+D+E, B+C+D+F C+D+E+F A+B+C+D+E+F 1.7 IMPEDANCECHART Impedance is a measurement of the load placed on your receiver/amplifier from thte control center will vary depending on how many pairs of 8-ohm speakers. The chart below shows the impedance for all possible combinations of speakers you turn on at one time, and on which speakers you turn on your receiver/amplifier by the speakers.
... A+B+C, A+B+D, A+B+E A+B+F, A+C+D, A+C+E A+C+F, A+D+E, A+D+F A+E+F, B+C+D, B+C+E 3.1 B+C+F, B+D+E, B+D+F C+D+E, C+D+F, D+E+F A+B+C+D, A+B+C+E 2.4 A+B+C+F, A+C+D+E A+C+D+F, A+D+E+F B+C+D+E, B+C+D+F C+D+E+F A+B+C+D+E+F 1.7 IMPEDANCECHART Impedance is a measurement of the load placed on your receiver/amplifier from thte control center will vary depending on how many pairs of 8-ohm speakers. The chart below shows the impedance for all possible combinations of speakers you turn on at one time, and on which speakers you turn on your receiver/amplifier by the speakers.
Owners Manual
Page 7
SPECIFICATIONS Audio Power Handling Frequency Response Channel Separation Crosstalk between channels Speaker terminal wire size requirements Dimensions (WxHxD) Weight 50W (R.M.S.)/ch, 100W (Max)/ch 20 Hz to 20KHz 80 dB 50 dB 14-22 awg 190x50x120 mm (PSS4) 250x50x150 mm (PSS6) 0.81kgs (1.79lbs) (PSS4) 1.15kgs (2.54lbs) (PSS6) PYLE AMPLIFIERS CAR AMPLIFIERS
SPECIFICATIONS Audio Power Handling Frequency Response Channel Separation Crosstalk between channels Speaker terminal wire size requirements Dimensions (WxHxD) Weight 50W (R.M.S.)/ch, 100W (Max)/ch 20 Hz to 20KHz 80 dB 50 dB 14-22 awg 190x50x120 mm (PSS4) 250x50x150 mm (PSS6) 0.81kgs (1.79lbs) (PSS4) 1.15kgs (2.54lbs) (PSS6) PYLE AMPLIFIERS CAR AMPLIFIERS