Instruction Manual
Page 2
... registered trademark of Wi-Fi Alliance. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY 7 HOW TO USE THE TREADMILL 18 HOW TO FOLD AND MOVE THE TREADMILL 30 MAINTENANCE AND TROUBLESHOOTING 31 EXERCISE GUIDELINES 35 PART LIST 38... call the telephone number on the front cover of the warning decals. Note: The decals may not be shown at actual size. 305284 PROFORM and IFIT are registered trademarks of Google LLC. The Bluetooth® word mark and logos are registered trademarks of Wi-Fi Alliance. 2 ...
... registered trademark of Wi-Fi Alliance. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY 7 HOW TO USE THE TREADMILL 18 HOW TO FOLD AND MOVE THE TREADMILL 30 MAINTENANCE AND TROUBLESHOOTING 31 EXERCISE GUIDELINES 35 PART LIST 38... call the telephone number on the front cover of the warning decals. Note: The decals may not be shown at actual size. 305284 PROFORM and IFIT are registered trademarks of Google LLC. The Bluetooth® word mark and logos are registered trademarks of Wi-Fi Alliance. 2 ...
Instruction Manual
Page 4
Adjust the speed in small increments to move the treadmill until it is properly assembled. (See ASSEMBLY on page 7 and HOW TO FOLD AND MOVE THE TREADMILL on page 5 for the location of the power switch), and unplug the power cord when ...
Adjust the speed in small increments to move the treadmill until it is properly assembled. (See ASSEMBLY on page 7 and HOW TO FOLD AND MOVE THE TREADMILL on page 5 for the location of the power switch), and unplug the power cord when ...
Instruction Manual
Page 6
..." x 1 1/4" Screw (29)-6 3/8" x 1 1/4" Screw (20)-4 3/8" x 2 3/4" Screw (23)-4 6 The number in the hardware kit, check to identify small parts used for assembly. The number following the key number is the quantity used for assembly. PART IDENTIFICATION CHART Use the drawings below each drawing is the key number of the part, from the PART LIST...
..." x 1 1/4" Screw (29)-6 3/8" x 1 1/4" Screw (20)-4 3/8" x 2 3/4" Screw (23)-4 6 The number in the hardware kit, check to identify small parts used for assembly. The number following the key number is the quantity used for assembly. PART IDENTIFICATION CHART Use the drawings below each drawing is the key number of the part, from the PART LIST...
Instruction Manual
Page 7
...number, serial number, and name of the treadmill. This is an oily substance on the front cover of this manual) 7 ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • After shipping, there may be an oily substance on the exterior of your product (see page 6. ...• Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • Assembly requires the following tools: the included hex key one adjustable wrench one Phillips screwdriver To avoid damaging parts, do not have internet access, call ...
...number, serial number, and name of the treadmill. This is an oily substance on the front cover of this manual) 7 ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • After shipping, there may be an oily substance on the exterior of your product (see page 6. ...• Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • Assembly requires the following tools: the included hex key one adjustable wrench one Phillips screwdriver To avoid damaging parts, do not have internet access, call ...
Instruction Manual
Page 10
Be careful not to pinch the Upright Wire (83) on the Handrails (74). Attach the console assembly (G) with the four 5/16" x 2" Screws (2) that you removed in step 5 and four 5/16" Star Washers (8); 6. Be 7 careful not to the Right and Left Uprights (84, ... 5/16" Star Washers (8); Then, remove and discard the two indicated screws (F). 6 2 8 F 74 91 2 83 8 74 F 84 7. With the help of a second person, set the console assembly (G) on the right side. do not fully tighten the Screws yet. 74 8 H 29 G 74 8 29 10 Attach the two Handrails (74) to pinch the wires...
Be careful not to pinch the Upright Wire (83) on the Handrails (74). Attach the console assembly (G) with the four 5/16" x 2" Screws (2) that you removed in step 5 and four 5/16" Star Washers (8); 6. Be 7 careful not to the Right and Left Uprights (84, ... 5/16" Star Washers (8); Then, remove and discard the two indicated screws (F). 6 2 8 F 74 91 2 83 8 74 F 84 7. With the help of a second person, set the console assembly (G) on the right side. do not fully tighten the Screws yet. 74 8 H 29 G 74 8 29 10 Attach the two Handrails (74) to pinch the wires...
Instruction Manual
Page 13
... Screws. 13 32 24 24 G 94 24 24 13 12. tighten the Truss Head Screws. Attach the Right Handrail Bottom Cover (82) to the console assembly (G) with two #8 x 3/4" Truss Head 12 Screws (24); Be careful not to the left Handrail (74) with six #8 x 3/4" Truss Head Screws (24); Attach the Left Handrail...
... Screws. 13 32 24 24 G 94 24 24 13 12. tighten the Truss Head Screws. Attach the Right Handrail Bottom Cover (82) to the console assembly (G) with two #8 x 3/4" Truss Head 12 Screws (24); Be careful not to the left Handrail (74) with six #8 x 3/4" Truss Head Screws (24); Attach the Left Handrail...
Instruction Manual
Page 17
.... 20 Start First 3 100 3 N G 21. Make sure that all parts are sheets of plastic on the Tablet Holder (100) into the slots (N) in the console assembly (G). Attach the Tablet Holder (100) with most full-size tablets. If there are properly tightened before you use with four M4 x 16mm Screws (3). Note: Start...
.... 20 Start First 3 100 3 N G 21. Make sure that all parts are sheets of plastic on the Tablet Holder (100) into the slots (N) in the console assembly (G). Attach the Tablet Holder (100) with most full-size tablets. If there are properly tightened before you use with four M4 x 16mm Screws (3). Note: Start...