Pfaff hobby 1010-1037 Support and Manuals
Get Help and Manuals for this Pfaff item
This item is in your list!
View All Support Options Below
Free Pfaff hobby 1010-1037 manuals!
Problems with Pfaff hobby 1010-1037?
Ask a Question
Free Pfaff hobby 1010-1037 manuals!
Problems with Pfaff hobby 1010-1037?
Ask a Question
Popular Pfaff hobby 1010-1037 Manual Pages
Owner's Manual - Page 1
INSTRUCTION MANUAL FOR SEWING MACHINE
0]
351427004 0012.14
Hobby Model 1010 - 37
Owner's Manual - Page 2
...
22
Embroidery
22
Quilter & Seam guide
23
Buttonhole sewing
24
Maintenance (Cleaning and oiling)
25
Checking Performance Problems WHAT TO DO
26 WARNING To reduce the risk of electric shock:
An appliance should always be followed, including the following:
Read all instructions before using and before relamping, Replace bulb with any adjustments in the...
Owner's Manual - Page 3
NAME OF PARTS (FRONT VIEW)
(REAR VIEW)
Zigzag width dal resure Regulator
Take up lever
Thread tension dial
Presser toot Shuttle
Extension table
Sub-spool pin pin Top cover Needle position knor Reverse button d al
read guide for upper threading
Bobbin winder
Bobbin winder spindle Upper thread guide
Stop Motion knob Hand wheel
Face...
Owner's Manual - Page 4
... the sewing machine unattended, the plug must be removed from the socket outlet.
-4- When servicing the sewing machine, or when removing covers or changing lamps, the machine must be disconnected ...plug from the socket outlet. Button foot
Machine Oil
Zipper foot
Button hole cutter
Screw driver
-3- Install a now bulb by unscre ing it counter-clockwise.
3.
I Needle #11 #14
Sewing ...
Owner's Manual - Page 5
... is filk tighten stop motion kric
2.Thread as shown at side.
-5-
5cm thread
Push bobbin winder spindle in correct, release .the screw of upper thread guide and ad just up or down until bobbin winding is in direction of arrow.
Owner's Manual - Page 6
... to its highest position, pulling thread to its highest
zposition and open the latch of bobbin case and hold it into
bobbin case as shown.
2.Guide the end of thread into slot and under
tension spring and draw out about 10cm of thread.
-7-
INSERTING BOBBIN INTO BOBBIN CASE
insertI.PulI off...
Owner's Manual - Page 9
Insufficient pressure may cause poor feeding, skipped stitches, or difficulty in guiding the fabric.
4.
With the flat side of the needle facing away from you,
insert needle as far up to raise feed above needle plate for ...
Owner's Manual - Page 10
...suitable to sew.
5. Attention 1, When 'turning the balance wheel manually, always turn it
toward, you stop sewing.
-15-
16 -
- FABRIC THREAD NEEDLE TABLE
Please note that the following list is a guide when sewing different fabrics. Depress foot/Speed control and start to... lever to the rear of machine for the length of the fabric when you .
2.Guide the cloth gently with your fabric.
Owner's Manual - Page 11
..., use smaller stitch size. (Refer to rear of stitching is the one used most frequently. 2.The zig-zag presser foot can be used for dial
setting). STRAIGHT STITCH
1 This type of
machine.
5.Cut threads as shown on the thread cutter. - 17-
TO FINISH SEAM
1 .Sew to the edge of seam. 2.Push...
Owner's Manual - Page 12
... set the zipper foot on the left side of the needle. 2. sew as illustrated.
20 -
- BLflTON SEWING
1 .Lower drop feed. 2. ZIPPER SEWING
Select straight stitch. 1. Place zipper foot In position and attach firmly 3.
Place button attaching presser foot in position. 3.Place button between presser foot and fabric and lower presser foot. 4.Manually...
Owner's Manual - Page 13
...hemmer foot.
2.
Insert other thread into the
hemmer foot. 5. See Page 13 drop teed
-22- Replace the toot with a few stitches. The
fabric must be fed in to run into the left a...and allow it under the foot. Separate threads before last thread guide above the needle.
CAUTION:Do not set stitch width wider than number 2 setting. Lower the foot and sew the hem. 4. E,cceeding ...
Owner's Manual - Page 14
... FROM THE MACHINE AND OPEN ThE BUTTONHOLE WITH A BUTTONHOLE CUT OR SEAM CUTTER.
(1)
p
r(2)
(3)
(4)
01
41
1. Run machine with cutter as shown.
Set guide hole on top of material touching guide.
23 -
- SET STITCH LENGTH ABOUT 0.5, ZIGZAG WIDTh KNOB ABOUT '2' NEEDLE POSITION KNOB ON L POSITION, THEN SEW AS FIGURE (2) IJNTILL YOU REACHES THE END OF...
Owner's Manual - Page 15
... not moving . . Machine not moving
Breaking Needle
Breaking Bobbin Thread
CHECKING PERFORMANCE PROBLEMS WHAT TO DO
PROBABLE CAUSE
- Incorrect setting of fabric, and
thread. Tight upper thread tension. - Moving dial to 1 -4. -
Replace shuttle, or polish off
burrs completely. C)
CDDC
CD CCDD
C. 0. CCD. Feed dog down. - Tight stop motion. - Do not pull fabric. - Machine...
Pfaff hobby 1010-1037 Reviews
Do you have an experience with the Pfaff hobby 1010-1037 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Pfaff yet.
Earn 750 points for your review!