Pfaff 1196-1197 Support and Manuals
Get Help and Manuals for this Pfaff item
View All Support Options Below
Free Pfaff 1196-1197 manuals!
Problems with Pfaff 1196-1197?
Ask a Question
Free Pfaff 1196-1197 manuals!
Problems with Pfaff 1196-1197?
Ask a Question
Popular Pfaff 1196-1197 Manual Pages
Owner's Manual - Page 2
...lead of machine arm>
1 9 Needle holder with needle set screw
20 ...code: Blue: Neutral: Brown: Live. '..' 7'."-, '•IILJ IIIdIiIIIIe
Some safety rules a) Be careful when sewing that your fingers will not be connected to interrupt sewing and leave the machine...machines) 1 3 Bed cover 14 Sewing foot 1 5 Thread cutter (on presser bar)
On Model 1 209 dual feed with thread cutter 1 6 Upper ...
Owner's Manual - Page 3
... Zigzag stitch Needle position Reverse sewing and dropping the feed dog Presser bar lifter Dual feed. 1209 Thread tensions Changing the needle Changing the sewing foot Utility stitches Utility-stitch combinations Sewing buttonholes Sewing feet Special accessories Changing the light bulb Cleaning and oiling Threading the needle 1209 Trouble shooting
Model 1196/1197 Press down catches A (marked by...
Owner's Manual - Page 4
... The handle can be folded down, as shown by catches and can thus be placed in the drawer.
4
-/
B. Foot control receptacle Models 11 99/1209 Remove the receptacle from the machine.
Before you put the machine away after sewing, replace the receptacle in its original position (A>, and push it onto the free arm. Accessories drawer...
Owner's Manual - Page 5
... needle.
To do this, hold the balance wheel steady and turn the knob in the opposite direction to re-engage the sewing
mechanism again. Your machine is depressed, the faster the machine will run.
Press down its pedal. Lift latch K, pull Out the bobbin case, release the latch and take out the bobbin...
Owner's Manual - Page 6
...the bobbin case onto stud B, making sure slot A points upwards.
Bobbin winding Disengage the sewing mechanism. Inserting the bobbin Insert the filled bobbin into place. Release the latch and lightly ... stops automatically when the bobbin is full. Re-engage the sewing mechanism. Then pull it around thread retainer stud 2, wind it into guides C and D. Place a spool of thread on the bobbin...
Owner's Manual - Page 7
... its guide pins enter the two holes, then lower it,
Attaching the work support, Model 1196/1197 11 ...96: Turn over the free arm (B) until the needle moves down and up again and the take-up lever is up the bobbin thread Hold the needle thread a little taut.
Turn balance wheel 7 toward the left and back under the sewing foot. Attaching the work support, Model...
Owner's Manual - Page 8
... the presser bar which serves as a thread cutter. Zigzag stitch Setting mark = A Zigzag stitches are close together;
Pull the work back out of the machine, Place the threads over thread cutter 22 and pull them downwards to cut them .
Thread cutter, Models 1196/1199 There is located at the back of dual feed 1 5. Raise the sewing foot.
Owner's Manual - Page 9
Needle position The needle can be set to raise the needle and take-up lever 1.) B = The sewing foot is dropped
(for sewing. The machine sews
permanently in the needle hole.
Dual feed, Model 1209 This additional feed prevents one ply from creeping ahead of the needle position desired is positioned below mark A.
= central needle position (normal)
= right needle position
= left...
Owner's Manual - Page 10
...Both tensions are correct. = Upper tension too loose or lower tension too tight. Loosen screw A until the sewing foot can be removed by its shank facing toward the back> and push it up as far as it ...downwards when you jerk your hand upwards lightly. Then tighten screw A. The normal tension
setting is in the green range between 3 and 5. Then hold the needle, loosen screw A and pull ...
Owner's Manual - Page 11
... C Elastic triple straight stitch D Overlock stitch E Cross stitch 3 Eraser button for a specific utility stitch is required for releasing the pushed
buttons.
Utility-stitch setting The setting of Stitches.
4
O-2A\ A
V
1
//
-
=
JHLJL =
=
± I!
+ ±
+I Honeycomb stitch
Setting: buttons A+C, straight stitch 4, left needle position, turn control 1 7 to vertical position...
Owner's Manual - Page 13
... fabrics silk lersey. I Cording foot;
for fine cording needle size 701
For sewing fringes arid for ornamental sewing and sewing on buttons. Sewing feet A Normal sewing foot, Models
1196-1199 O Normal sewing foot, Model 1 209;
for all sewing operations requiring no special sewing foot. ccessory
Cordvig set
Coroing fool, 3 grooves (twin needle with 2.5 or 3.0mm needle gauge)
Cording...
Owner's Manual - Page 14
...parts in the vicinity of oil into the hook raceway.
Push control 25 down all the way. Threading the needle 1209 Turn the balance wheel toward B. Remove the bobbin case. Do not oil the machine because it out. 1197...thread is maintenance-free, but now and then put a drop of the sewing hook and the feed dog with a soft brush. Open cover 24.
Changing the light bulb Push the light bulb...
Owner's Manual - Page 15
...up as far as it will go. Let machine feed the work is not uniform Tension out of oil into place.
24
/ Cause:
4. Only guide the material lightly.
rows of material.
Remove ...control is at all
Lint has accumulated between tooth
Remove needle plate and clean out lint.
Machine feeds irregularly or not at left.)
6. Needle bent and strikes needle plate because work alone.
...
Pfaff 1196-1197 Reviews
We have not received any reviews for Pfaff yet.