Panasonic MCV5734 - UPRIGHT VACUUM Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic MCV5734 manuals!
Problems with Panasonic MCV5734?
Ask a Question
Free Panasonic MCV5734 manuals!
Problems with Panasonic MCV5734?
Ask a Question
Popular Panasonic MCV5734 Manual Pages
MCV5734 User Guide - Page 2
... are not followed. Replace worn or frayed power cord immediately. The use of damage to prevent accidents such as tripping over power cord or machine.
Store machine promptly after each use and safety information. All rights reserved.
- 2 -
Always check the carpet or floor covering manufacturer's recommended cleaning instructions before servicing. not chairs, tables...
MCV5734 User Guide - Page 5
...this manual.... toy. DO NOT use in your local supply.
- 5 - IMPORTANT SAFETY INSTRUCTIONS
When using vacuum cleaner, basic precautions should , has been dropped, damaged, left...parts. 11. To unplug, grasp the plug, not the cord. 8. keep free of fire or electric shock - DO NOT use without belt cover properly installed. Keep hair, loose clothing, fingers, and all controls before servicing...
MCV5734 User Guide - Page 8
TABLE OF CONTENTS
CONSUMER INFORMATION 2 IMPORTANT SAFETY INSTRUCTIONS 5 PARTS IDENTIFICATION 10 FEATURE CHART 11
ASSEMBLY ...12 ..., 26 Removing and Installing Lower Plate 28 Replacing Headlight Bulb 30 Replacing Belt 30, 32 Cleaning Agitator 32 Replacing Agitator 34 Agitator Assembly 34 Cleaning Exterior and Tools 34 Removing Clogs...36
BEFORE REQUESTING SERVICE 38 WARRANTY ...41...
MCV5734 User Guide - Page 14
...wand.
➢ Place crevice tool into rectangular rear slot of tool holder.
➢ Refer to PARTS IDENTIFICATION section for tool location.
- 14 - Tool Storage
Wand
Tube Tubo
Crevice Tool
Suceur plat
...para sacudir
➢ Some tools may already be stored on wand with dusting brush in hose, guide tabs along grooves, twist to rewind the cord.
Wand
Tube Tubo
"J" Slot
Fente en "J" ...
MCV5734 User Guide - Page 16
... when dust bag needs changing.
➢ Motor protector may open when using tools.
➢ Check operation by placing hand over carpet pile surfaces.
➢ No manual adjustments required. Edge Cleaning
➢ Edge cleaning feature enables improved cleaning of carpets near walls and furniture.
MCV5734 User Guide - Page 18
... turns vacuum on handle release pedal to change
handle position.
2) ➢ Move vacuum to upright position for
storage and tool use.
3) ➢ Move vacuum to install the proper outlet.
DO NOT CHANGE THE PLUG IN ANY WAY. ON-OFF Switch
➢ Ensure ON-OFF switch is wider than the other. Only...
MCV5734 User Guide - Page 20
... Brush may be used on the following items: • Furniture • Drapes • Stairs • Walls
Hose Ring and Hose Ring Mount
Hose Ring Mount Support de l'anneau du tuyau Soporte para anillo para manguera
➢ Hose ring and hose ring mount are designed to prevent tipping of vacuum while using...
MCV5734 User Guide - Page 22
...Rainures Lengüetas
➢ Secondary foam filter protects the motor.
➢ Check filter when installing a new dust bag.
➢ If dirty, pull filter from bottom of these high levels for... of dust compartment and clean by rinsing in this manual for years to help solve various problems that may occur. Check the BEFORE REQUESTING SERVICE section in water.
➢ When dry, place ...
MCV5734 User Guide - Page 24
... bag, taking care
not to tear bag.
- 24 - Changing Dust Bag
Always operate vacuum with genuine Panasonic Type U3 Standard or U6 Electrostatic dust bags installed. Panasonic dust bags may be purchased through any authorized Panasonic dealer or ordered from...
MCV5734 User Guide - Page 28
...10146; Remove lower plate and remove any parts, disconnect vacuum from cleaner suddenly starting. WARNING Electrical Shock or Personal Injury Hazard
Disconnect the electrical supply before servicing or cleaning the unit. Removing and Installing Lower Plate
Three Screws
Trois vis Tres ... routed properly and not pinched.
➢ Press lower plate into place then replace three (3) screws.
- 28 -
MCV5734 User Guide - Page 32
...; Clean agitator after every five uses and every time the belt is not
twisted or pinched and that all rotating
parts turn it by
hand to make sure that belt is replaced.
➢ Remove lower plate. ➢ Cut off any carpet pile and lint entangled
around agitator with a pair of scissors. ➢...
MCV5734 User Guide - Page 34
Card
Carte Tarjeta
Replacing Agitator
➢ When the bristles on the agitator are worn so that has been dipped in warm ...10146; Clean exterior using a clean, soft cloth that they do not touch a card held across the lower plate, the agitator should be replaced.
➢ Remove lower plate and agitator.
➢ Clean debris from end caps.
➢ Position belt over belt pulley on cleaner, ...
MCV5734 User Guide - Page 38
... starting. Reset circuit breaker or replace fuse.
1. Broken belt. 3. Clean hose or nozzle area. 4. PROBLEM
Cleaner will not work. Full or clogged dust bag. 2. Bag improperly installed. 2. Bag torn.
1. Push ON-OFF switch to find do so could result in these Operating Instructions, should be performed by an authorized service representative. Hole in firmly. Change...
MCV5734 User Guide - Page 41
... or other business or rental use of the product, or service by calling the local Panasonic Sales Company telephone number listed in the U.S.A. If a problem with this product with new or refurbished parts free of a defect in shipment, or failures which require normal replacement: Disposable Dust Bag, Filters, Belts, Light Bulbs, Agitator Brushes and...
MCV5734 User Guide - Page 42
...OR FITNESS FOR A PARTICULAR PURPOSE. WARRANTY SERVICE
For product operation and information assistance, ...238-2360
Web: www.panasonic.ca
For product repairs, please contact one of the following: •...in any product which has been improperly installed, subjected to be applicable.
Calgary, AB...A. Vacuum Cleaner - One (1) year, parts and labour
LIMITATIONS AND EXCLUSIONS This warranty does...
Panasonic MCV5734 Reviews
We have not received any reviews for Panasonic yet.