Panasonic MCV5204 - COMMERCIAL VACUUM Support and Manuals
Get Help and Manuals for this Panasonic item
This item is in your list!
View All Support Options Below
Free Panasonic MCV5204 manuals!
Problems with Panasonic MCV5204?
Ask a Question
Free Panasonic MCV5204 manuals!
Problems with Panasonic MCV5204?
Ask a Question
Popular Panasonic MCV5204 Manual Pages
MCV5204 User Guide - Page 2
... CAUTION
WARNING statements are not followed. Replace worn or frayed power cord immediately. All rights reserved.
- 2 - Proper assembly and safe use and before servicing.
not chairs, tables, steps, stairs, etc. DO NOT store machine outdoors. TO AVOID ACCIDENTS
Except for purchasing this product. Read and understand all instructions. Thank you to the vacuum...
MCV5204 User Guide - Page 5
... described in this manual before unplugging.
15. Do not put on ...9. Read all instructions in areas where they may reduce air flow.
13. Disconnect electrical supply before servicing.
5. Close attention...INSTRUCTIONS
WARNING
To reduce the risk of fire, electrical shock, injury: When using your vacuum cleaner.
2. To unplug, grasp the plug, not the cord.
10. Turn off all parts...
MCV5204 User Guide - Page 8
... Tool Usage...22
ROUTINE CARE OF VACUUM CLEANER 24 Replacing Secondary HEPA Filter 24 Changing Dust Bag ...26 Removing and Installing Lower Plate 28 Replacing Belt...30 Cleaning Agitator...32 Replacing Brushes ...32 Agitator Assembly ...34 Cleaning Exterior and Tools 34 Removing Clogs ...36
BEFORE REQUESTING SERVICE 38 WARRANTY...41, 42 WHAT TO DO WHEN...
MCV5204 User Guide - Page 10
... is for electric current to whether the outlet is properly installed and grounded in accordance with all local codes and ordinances.
GROUNDING INSTRUCTIONS
Grounded Outlet
Prise avec contact de mise à la terre... rating plate located at the back of electric shock. Check with a qualified electrician or service person if you plug in a risk of the vacuum cleaner is the same as your...
MCV5204 User Guide - Page 16
... hose holder.
➢ Attach wand to hose by aligning the two (2) raised tabs on wand with "J" slots in hose, guide tabs along grooves, twist to lock in place.
➢ Place wand in middle slot of tool holder, twisting and pushing down...of tool holder.
➢ Place crevice tool into rectangular rear slot of tool holder.
➢ Refer to PARTS IDENTIFICATION section for tool location.
- 16 -
MCV5204 User Guide - Page 24
... installing a new dust bag.
➢ If dirty, pull filter from bottom of these tasks to come. Check the BEFORE REQUESTING SERVICE section...replaced at peak performance levels and will keep your new Panasonic vacuum cleaner operating at least once each year.
- 24 - CARPET BARE FLOOR (TOOLS)
➢ Place new filter, white side up, in this manual for years to help solve various problems...
MCV5204 User Guide - Page 26
Changing Dust Bag
Always operate vacuum with genuine Panasonic Type U3 Standard or U6 Electrostatic dust bags installed.
Panasonic dust bags may be purchased through any authorized Panasonic dealer or ordered from service company.
1) ➢ Pull outward on dust cover grip to
remove the dust cover.
2) ➢ Remove dust bag by holding cardboard...
MCV5204 User Guide - Page 28
... Electrical Shock or Personal Injury Hazard
Disconnect the electrical supply before servicing or cleaning the unit.
Lower Plate Plaque inférieure Base... snap into place, then push two (2) latches outward.
- 28 - Latches Taquets Lengüetas
Removing and Installing Lower Plate
➢ Always place paper under nozzle whenever lower plate is removed to do so could result in electrical...
MCV5204 User Guide - Page 30
...; Remove lower plate.
➢ Remove agitator by hand to make sure that belt is not twisted or pinched and that all rotating parts turn freely.
➢ Reinstall lower plate.
+
+
+
Replacing Belt
➢ Replace belt whenever a burning rubber smell caused by excessive slippage occurs. Groove Ranura Ouverture
End Cap Tapa del extremo Bouchon
- 30 -
MCV5204 User Guide - Page 32
... l'agitateur Polea del agitador
Agitator Holder Support de l'agitateur Soporte del agitador
➢ Install new brushes by reversing procedure.
➢...lower plate, the brushes should be replaced.
➢ Remove lower plate and agitator. Replacing Brushes
Card Carte Tarjeta
➢ ...➢ Push each brush out of parts.
Brush Brosse Cepillo
➢ Position belt over agitator pulley on the...
MCV5204 User Guide - Page 38
... minor performance problems. Any service needed, other than those described in firmly. ON-OFF switch not turned on motor shaft. Plug in these Operating Instructions, should be performed by an authorized service representative. Push ON-OFF switch to ON.
2. Reset circuit breaker or replace fuse. Full or clogged dust bag. 2. Dust cover improperly installed. 8. Clean hose...
MCV5204 User Guide - Page 41
... covers failures due to acts of original purchase will repair this product with this product develops during normal use and ...SET FORTH ABOVE. Carry-in or mail-in service in shipment, or failures which result from state to the original purchaser. If the problem...specific legal rights and you . If a problem with new or refurbished parts free of a defect in materials or workmanship.
MCV5204 User Guide - Page 42
... the original end user purchaser only. WARRANTY SERVICE
For product operation and information assistance, please contact...(905) 238-2360
Web: www.panasonic.ca
For product repairs, please contact one of the following: • Your ...installed, subjected to usage for a period as disposable dust bags, filters, belts, light bulbs and agitator brushes are also excluded from the performance. Parts...
Panasonic MCV5204 Reviews
Do you have an experience with the Panasonic MCV5204 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Panasonic yet.
Earn 750 points for your review!