EY7440 User Guide
Page 4
... 1) Ensure the switch is in the manner intend ed for one terminal to be ejected from battery; avoid contact. Contact with the charger spe cified by holding the speed control trigger halfway (speed control mode) so that this happens, release the speed control trigger...power tool or these instructions and in the off to prevent an overload which can cause hearing loss. 2) Be aware that the motor stops. A charger that is maintained. If this tool is always in the hands of injury and fire. 4) When battery pack is on invites accidents. 2) Recharge only...
... 1) Ensure the switch is in the manner intend ed for one terminal to be ejected from battery; avoid contact. Contact with the charger spe cified by holding the speed control trigger halfway (speed control mode) so that this happens, release the speed control trigger...power tool or these instructions and in the off to prevent an overload which can cause hearing loss. 2) Be aware that the motor stops. A charger that is maintained. If this tool is always in the hands of injury and fire. 4) When battery pack is on invites accidents. 2) Recharge only...
EY7440 User Guide
Page 5
...will not be stepped on plug of injury, charge only Panasonic Battery Pack as specified below. wire size is large enough for battery charger EY0L80. 2) Before using battery charger, read all instructions and cautionary markings on battery charger, battery pack, and product using the tool from chemi... the risk of damaging the electric plug and cord, pull by power sanding, sawing, grinding, drilling, and other - - RECOMMENDED MINIMUM AWG SIZE OF EXTENSION CORDS FOR BATTERY CHARGERS AC Input Rating. Other types of batteries may result in good electrical condition. take it to ...
...will not be stepped on plug of injury, charge only Panasonic Battery Pack as specified below. wire size is large enough for battery charger EY0L80. 2) Before using battery charger, read all instructions and cautionary markings on battery charger, battery pack, and product using the tool from chemi... the risk of damaging the electric plug and cord, pull by power sanding, sawing, grinding, drilling, and other - - RECOMMENDED MINIMUM AWG SIZE OF EXTENSION CORDS FOR BATTERY CHARGERS AC Input Rating. Other types of batteries may result in good electrical condition. take it to ...
EY7440 User Guide
Page 6
... place and open the chuck jaws by turning the lock collar and tighten the screw (left-handed screw) with a keyless drill chuck. 1. Do not change the plug in any other charger. 14)Do not attempt to disassemble the battery pack housing. 15)Do not store the tool and battery pack in locations where... the temperature may result in a polarized outlet only one way. NOTE: If excessive play occurs in the chuck, secure the drill in order to install...
... place and open the chuck jaws by turning the lock collar and tighten the screw (left-handed screw) with a keyless drill chuck. 1. Do not change the plug in any other charger. 14)Do not attempt to disassemble the battery pack housing. 15)Do not store the tool and battery pack in locations where... the temperature may result in a polarized outlet only one way. NOTE: If excessive play occurs in the chuck, secure the drill in order to install...
EY7440 User Guide
Page 11
...the charging lamp does not flash quickly in green, consult an authorized dealer. 8. If the power lamp does not light immediately after the charger is 0°C or less, charging takes longer to fully charge the battery pack than the standard charging time. Alignment marks 3. Ni-MH...may flash quickly to prevent overcharging. • Charging will have approximately 50% of the power of safety. 2. Insert the battery pack firmly into the charger. 1 Line up to charge the battery before use . Even when the battery is inserted into the AC outlet. Be sure to full capacity. ...
...the charging lamp does not flash quickly in green, consult an authorized dealer. 8. If the power lamp does not light immediately after the charger is 0°C or less, charging takes longer to fully charge the battery pack than the standard charging time. Alignment marks 3. Ni-MH...may flash quickly to prevent overcharging. • Charging will have approximately 50% of the power of safety. 2. Insert the battery pack firmly into the charger. 1 Line up to charge the battery before use . Even when the battery is inserted into the AC outlet. Be sure to full capacity. ...
EY7440 User Guide
Page 12
... Charging will then begin when temperature of battery pack drops. When charging is plugged into the AC outlet. LAMP INDICATIONS Green Lit Charger is completed, the charging lamp will be flashing until the battery cools down. If the temperature of the battery pack goes up ... Green Flashing Battery is inserted into the AC power supply, but this is plugged in green, consult an authorized dealer. 6. Plug the charger into the charger. 3. Orange Lit Battery pack is not possible. Both Orange and Green Flashing Quickly Charging is cool. Clogged with dust or malfunction of ...
... Charging will then begin when temperature of battery pack drops. When charging is plugged into the AC outlet. LAMP INDICATIONS Green Lit Charger is completed, the charging lamp will be flashing until the battery cools down. If the temperature of the battery pack goes up ... Green Flashing Battery is inserted into the AC power supply, but this is plugged in green, consult an authorized dealer. 6. Plug the charger into the charger. 3. Orange Lit Battery pack is not possible. Both Orange and Green Flashing Quickly Charging is cool. Clogged with dust or malfunction of ...
EY7440 User Guide
Page 13
... cloth for cleaning. VII. SPECIFICATIONS MAIN UNIT Model Motor No load speed Chuck capacity Low High Clutch torque Overall length Weight (with battery pack: EY9L40) EY7440 14.4 V DC 60 - 400 /min (rpm) 200 - 1350 /min (rpm) ø 1.5 mm - ø 13 mm (1/16" - 1/2") Approx. 0.5 N·m (5 k f-...lbs) BATTERY PACK Model Storage battery Battery voltage Capacity EY9L40 Li-ion Battery 14.4 V DC (3.6 V × 4 cells) 3 Ah BATTERY CHARGER Model Electrical rating Weight EY0L80 See the rating plate on the bottom of drill's chuck. VI. VIII. Do not use a damp cloth, thinner, ...
... cloth for cleaning. VII. SPECIFICATIONS MAIN UNIT Model Motor No load speed Chuck capacity Low High Clutch torque Overall length Weight (with battery pack: EY9L40) EY7440 14.4 V DC 60 - 400 /min (rpm) 200 - 1350 /min (rpm) ø 1.5 mm - ø 13 mm (1/16" - 1/2") Approx. 0.5 N·m (5 k f-...lbs) BATTERY PACK Model Storage battery Battery voltage Capacity EY9L40 Li-ion Battery 14.4 V DC (3.6 V × 4 cells) 3 Ah BATTERY CHARGER Model Electrical rating Weight EY0L80 See the rating plate on the bottom of drill's chuck. VI. VIII. Do not use a damp cloth, thinner, ...