Panasonic BMED500 - CAMERA CONTROL UNIT Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic BMED500 manuals!
Problems with Panasonic BMED500?
Ask a Question
Free Panasonic BMED500 manuals!
Problems with Panasonic BMED500?
Ask a Question
Popular Panasonic BMED500 Manual Pages
BMED500 User Guide - Page 1
Control Unit
Operating Instructions
BM-ED500 Model No. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
BMED500 User Guide - Page 2
... ON-OFF switch is operated in the ON position. Unplug the power cord to rain or moisture.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
NO USER-SERVICEABLE PARTS INSIDE. SA 1965 SA 1966
The lightning flash with the instruction manual, may be placed on the bottom.
Operation of electric shock to constitute a risk of this book as...
BMED500 User Guide - Page 4
...22 I When the Door Trouble is Unrecoverable ...22 ADDITIONAL SYSTEM COMPONENTS ...23 I Iris Camera BM-ET500 ...23 I Administration Software BM-ES500E ...23 SPECIFICATIONS OF ELECTRICAL LOCK CONNECTORS (GATE 1 24 SPECIFICATIONS OF WIEGAND OUTPUT/RS-485 OUTPUT (GATE 2 24 SPECIFICATIONS OF ALARM OUTPUT CONNECTORS (ALARM OUT 25 TROUBLESHOOTING ...26 SPECIFICATIONS ...27 STANDARD ACCESSORIES ...27...
BMED500 User Guide - Page 5
...POWER
ALARM S3 S2 S1
is enrolled into the iris data by Iris Camera BM-ET500, is available for recognition). Refer to the manuals of BM-ES500E for details.
• As a control unit for ... plate-shaped film in front of the eyeball), which is generated from that of users need to install the optional Administration Software BM-ES500E onto a PC. PREFACE
Control Unit BM-ED500 is used in ...
BMED500 User Guide - Page 6
... access control systems. Any access control panel supporting the interface can also output signals to 3 iris cameras (2 external power supply devices for iris cameras) can be connected to the control unit. Refer to Administration Software BM-ES500E Administrator's Guide.
• One-time capturing of both of iris cameras (for enrollment and recognition) Up to RS...
BMED500 User Guide - Page 7
... FOR REPLACEMENT OR...DISASSEMBLE, REPAIR OR ...instruction manuals supplied to BM-ET500 Iris Camera describes operating instructions and installation guide of recognition cameras do not have to use Administration Software BM-ES500E: BM-ES500E Installation Guide
BM-ES500E Administrator's Guide BM-ES500E Backup Guide • BM-ES500E Installation Guide, Administrator's Guide, and Backup Guide...
BMED500 User Guide - Page 9
...; Replacement part Exchange the following parts for this product to qualified service personnel or system installers. Contact qualified service personnel for maintenance, etc. Use a dry cloth to clean the appliance when it down only by turning on the load bearing capacity of the installation surface and structure. If the surface is open this may erase the settings you...
BMED500 User Guide - Page 10
... to reset the control unit through the administration PC. (Refer to the administrator's guide of the control unit. (Refer to a receptacle controlled by using the supplied key...OUT CAMERA 3 CAMERA 2
SW1
CN1
CAMERA 1 CNCN904
CNCN911 CNT/TRM_2
w
tr
e
y
q Setting board
w Input/Output board
e Power board This board is used for safety. w Power indicator (POWER) Lights up when trouble occurs...
BMED500 User Guide - Page 11
... this knob. Error may occur.)
DSW1
12345678 OFF
I/F type selection
Setting
#3* #4* GATE 1
Electric lock I/F OFF OFF Electric lock
Wiegand out I/F ON OFF Deactivated
RS-485 out I /F selection should be same as the setting in the administration software. (Refer to the installation guide of the control unit. When you open the door for service personnel. w Setup indicator Shows...
BMED500 User Guide - Page 12
... to the installation guide of the control unit.
Up to 3 iris cameras are configurable through the administration PC. (Refer to one camera may cause trouble. w Alarm input/output connectors (ALARM IN, ALARM OUT) ALARM IN: These connectors are connectors to output the alarm signal from the control unit to supply iris cameras with iris camera model BM-ET500...
BMED500 User Guide - Page 13
... electricity.
• This unit is for indoor use
13 System Instruction (Maximum System)
Coaxial cable (BNC)
Coaxial cable (BNC)
Camera power cable
OK NG
BM-ET500 (For recognition)
OK
BM-ET500... box was not evaluated by qualified service personnel or system installers. I Caution on Installation
Secure the control unit with the National Electrical Code (NFPA70), and the local authorities ...
BMED500 User Guide - Page 18
... you make iris cameras enroll people. Then, the recognition procedures with the supplied key. Pull the door sensor. 3. Operation mode Description and setting
IP setting mode
This is stopped.
2. In addition to notify you open . SETUP mode
Set to this mode when you change the operation mode to the installation guide and administrator's guide of the administration software...
BMED500 User Guide - Page 19
...settings of LAN, which connects the control unit. IP address setting command: "113✽002#" Subnet mask setting command: "113✽003#" Gateway setting command: "113✽004#"
4. Completed: 0 Failed: 1 (The address may be wrong.) Parameter error...the
Waiting an entry
mode setting
3. Wait until the Setup indicator changes from 0 to 99 to the IP setting mode.
2. Address will ...
BMED500 User Guide - Page 22
...22 In this case, turn off the power immediately and refer to service personnel. (Refer to p.21 for how to inform you of the trouble status. In this case, turn off and turn on the power...on the lock type. However, be opened with the lock deactivation. I When the Door Trouble is Unrecoverable
When trouble has occurred to the door and it is unrecoverable, all the indicators (POWER, ALARM,...
BMED500 User Guide - Page 26
...of the external powercontrol device may be turned off .
TROUBLESHOOTING
Check the following before requesting repair.
The power of the external devices. (Refer to...Turn on the power of the external devices may be turned off . Problem POWER does not light up.
Check if the screws of the control...If a trouble cannot be supplied to p.8.)
External devices (such as electric locks) do not ...
Panasonic BMED500 Reviews
We have not received any reviews for Panasonic yet.