Panasonic AJSD955AP - DIGITAL VCR Support and Manuals
Get Help and Manuals for this Panasonic item
This item is in your list!
View All Support Options Below
Free Panasonic AJSD955AP manuals!
Problems with Panasonic AJSD955AP?
Ask a Question
Free Panasonic AJSD955AP manuals!
Problems with Panasonic AJSD955AP?
Ask a Question
Popular Panasonic AJSD955AP Manual Pages
AJSD930 User Guide - Page 2
...contact either a local or foreign Panasonic authorized service center for U.S.A. Extension cords used...SETTING INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL. This equipment has been tested and found to comply with Part 15 of 100 - 240 V AC.
To assure continued compliance follow the attached installation instructions... for a class A digital device, pursuant to Part 15 of electric shock ...
AJSD930 User Guide - Page 3
Contents
Introduction 3
Features 4
Parts and their functions 5 Front panel 5 Display panel 11 Rear panel 13
Connections 15
Tapes 17
Jog/Shuttle 18
Manual editing SD955A 19
Preroll SD955A 19
Automatic editing (deck-to-deck) SD955A 20 Switch settings and adjustments 20 Selecting the editing mode 21 Registering the edit points 21 Checking and previewing...
AJSD930 User Guide - Page 4
...containing material shot with a consumer digital camera or the like can be recorded...setup The setup settings, which are performed while viewing the setup menus on this unit. Tape width is a standard feature. Compatibility with DVCPRO (25 Mbps) format
This unit can record, play back and edit material in TCG (time code generator)/TCR (time code reader). O 4-channel, high-sound-quality digital...
AJSD930 User Guide - Page 5
.../EBU digital signals CH3 : SDI input digital signals CH4...(50 Mbps) format tapes. Example:
Settings AUDIO button USER SET Setup menus No.715 (CH1 IN SEL...setup menu No. 115 (EJECT SW INH).
5 INPUT SELECT buttons These buttons switch the video and audio input signals. DVCPRO50: This indicates recording and playback of DVCPRO (25 Mbps) format tapes. Parts... been installed.
5 It is used...
AJSD930 User Guide - Page 8
...the case if ENA has been selected as the setup menu No. 313 (AUTO ENTRY) setting.
If this is used to the registered point... is pressed, the tape travels to locate where a transmission or manual editing starts on the counter display.
When it is cleared. The..., the point where it is executed using setup menu No. 000 (P-ROLL TIME). Parts and their functions
Front panel
L
JKIHE F...
AJSD930 User Guide - Page 9
...set of digits whose display is flashing is selected using the headphones. When it is pressed again, the setup menu settings are changed in tandem with the monitor output. When the internal time code has been set, the data which has been set...level control knobs These knobs are to be set to adjust the playback level, the PB LEVEL lamp lights.
Parts and their functions
Front panel
M
ON
...
AJSD930 User Guide - Page 11
...Digital audio signals
USER SET : Recording audio signal selection
SDI
: Serial digital audio signals
SDTI/1394 : Compressed digital...is lighted.
Parts and their ...setting setup menu item No. 070 (TV SYSTEM). The playback picture and sound remain unaffected even while this lamp is possible to indicate the error rate status. (green 5 white 5 red) Green: This lights when the error...
AJSD930 User Guide - Page 13
...OUT
L
3 (SUPER)
OPTION
SDTI
IN
OUT
CH3
CH4
MON
R
1
2
SERVICE ONLY
1 AC IN socket Connect one for IN/OUT use two of these VTRs...set ON or OFF is selected using setup menu No. 212 (MASTER PORT).
7 ENCODER REMOTE connector An external encoder remote controller is connected to this connector. Parts and their functions
Rear panel
1
AC IN
SIGNAL GND
2 3 4 5 6 7 8 9: ; The digital...
AJSD930 User Guide - Page 14
...setup menu No. 00 (WFM SEL). It is not a safety ground. D SDTI input and output connectors (optional) When the SDTI board (AJ-YAC930G, optional accessory) is installed in order to minimize noise. Whether the superimposing is to be set... to this VTR, digital data can be selected...VIDEO OUT 3 connector. Parts and their functions
Rear...
2
SERVICE ONLY
> ?@ A
BC D
< Fan...
AJSD930 User Guide - Page 15
...
L
3 (SUPER)
OPTION
SDTI
IN
OUT
CH3
CH4
MON
R
1
2
SERVICE ONLY
To video monitor device
To audio monitor device
Digital audio
To video monitor device
To audio monitor device
Analog video signal (component) OWhen the analog video input board (option) has
been installed. Connections
Source machine: Set the CONTROL switch on the front panel to...
AJSD930 User Guide - Page 19
...frame continuity) editing is rewound from the edit IN point for the period of time which was set by setup menu No. 000 (P-ROLL TIME), and it is to be continuously
recorded on the tape between... ASSEMBLE: Assemble (frame-to be edited. OThe time code or CTL must be terminated, and press the PLAY or STOP button at this mode. Manual editing SD955A
1 Select the editing mode. OIf the edit...
AJSD930 User Guide - Page 35
...picture and sound may be played back.
0000 MANUAL : The format complies with the format recorded on the tape.
After this setting is changed so that the
characters are output....setting of setup menu No. 012 (SYS FORMAT) when a DVCPRO cassette is inserted.
Setup menus
USER menu
No./Item
Description
009
This sets the position of the characters on the
horizontal plane for the time code...
AJSD930 User Guide - Page 40
...
306 EDIT RPLCE2
The same type of setting as setup menu No. 305. The same type of the VTR using a controller which does not have a digital audio edit preset control function. This selects... N-DEF : Not set again properly.
0001 AUTO : The edit points already input are processed. (Forced
NON-STD)
Use the non-standard (N-STD) setting when
video or audio trouble occurs with either analog...
AJSD930 User Guide - Page 55
... to select the set of digits that is to be recorded. Setting the internal time code
1 Set the VTR to stop... mode to slow-motion playback up to high-speed play (approx. 50a normal speed/approx. 100a when using setup menu No. 513 (RUN MODE). REGEN: In this mode, recording is commenced from the stop mode.
4 Set...
AJSD930 User Guide - Page 69
...specifications
External interface specifications
O Connector specifications Connector: D-SUB 25-pin (crossover cable supported...terminal ready (No processing)
Signal ground (Signal ground)
Data set ready (+ voltage output after communication enable status)
O Example ...DSR
69 O The setup menu No. 204 "RS232C SEL" must be at REMOTE. Whether the [ACK] code is returned depends on pages 72, 73.)...
Panasonic AJSD955AP Reviews
Do you have an experience with the Panasonic AJSD955AP that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Panasonic yet.
Earn 750 points for your review!