Oki OL840 Support and Manuals
Get Help and Manuals for this Oki Data item
Popular Oki OL840 Manual Pages
Troy Etherwind 802.11b Print Server Users Guide - Page 6
...129; MacOS 7.xx, 8.xx, 9.xx, MacOS X
Network Protocols Supported
TCP/IP • LPD/LPR • Raw TCP/IP...• Wireless Mode (Infrastructure or Ad-Hoc) • The SSID (service set identifier) for your wireless network. • The Radio Frequency Channel of ...; An 802.11b wireless enabled PC or Macintosh printing straight to the printer (Ad-Hoc or Peer-to-Peer Mode).
An 802.11b...
Troy Etherwind 802.11b Print Server Users Guide - Page 11
... printer is a problem. Verifying Successful Installation
...you will go through the following startup sequence:
It runs through a set of power-up diagnostics for a few seconds. Plug the power cord from another...made to the Troubleshooting section of ink, toner, paper, etc. Then print a test page by pushing the test switch and letting go out.
Connecting to a Printer
Follow these steps...
Troy Etherwind 802.11b Print Server Users Guide - Page 12
...the unit is power off.
To enable the console mode manually, unplug the power supply from the main menu, click...Data) on the TROY EtherWind to the equivalent output signals (e.g., Transmit Data) on how to an RS-232 Serial Device
Note: Skip this section if you to most printers.... The serial port can be set to operate in RTS out Not used Transmit Data Receive Data DSR in Signal Ground DTR out...
Troy Etherwind 802.11b Print Server Users Guide - Page 19
... using a Macintosh, no further configuration is necessary. • If your printer port, it will go to print under various operating systems is covered in chapters 4 through 9.
2-5 When you will need to manually assign a valid IP Address, Subnet Mask, and Gateway and then set the Boot Method to use a static address outside the range...
Troy Etherwind 802.11b Print Server Users Guide - Page 23
... on-screen instructions to complete this software uses the industry-standard TCP/IP protocol, it works transparently with IP routers and other IP-based equipment. Install the printer driver software according to the documentation for printing from Windows computers over an 802.11b wireless link.
Click the Windows Start button, select Settings, and then Printers. 4. Install the...
Troy Etherwind 802.11b Print Server Users Guide - Page 27
... the necessary zone.
3. Configuring the Macintosh
1. Setting Up Printing (MacOS 8.x and 9.x)
1. If you have a Postscript printer, you can print without any modification or special software ... information to use the LaserWriter driver.
4. Select the print server name (the default is selected.
Verify that Airport is connected, and install the printer driver.
2. At a Macintosh workstation...
Troy Etherwind 802.11b Print Server Users Guide - Page 31
... on the NetWare file server). Enter the name of the NDS Printer for the Queue name.
If you are configuring a bindery... OK. Select Print Services Quick Setup from a NetWare workstation.
6-3 Enter any unique name for the desired port in the Serviced Print Queues window.... The Type box should be left at the default Parallel setting.
7. Select the container where you must use the print ...
Troy Etherwind 802.11b Print Server Users Guide - Page 33
... EtherWind must be unique for any host computer that because this service), and enter the name of the normal BINARY_P1 service.
1. Berkeley UNIX Host Configuration
Berkeley UNIX host computers include Linux, Digital Equipment Corporation Digital UNIX, OSF/1, and ULTRIX; note that supports the Berkeley remote-LPR command can spool jobs to the network as...
Troy Etherwind 802.11b Print Server Users Guide - Page 35
... earlier
releases, may cause problems printing very long print jobs. For binary graphics files use the standard lp command; Enter the desired print server service name (BINARY_P1 for binary files or
TEXT_P1 for the printer name rather than NIS
or other name services. Due to Remote Printer is the default setting). Select Add ...
Troy Etherwind 802.11b Print Server Users Guide - Page 36
...(user selectable; Select Remote printer queues 6. You should now be used with the printer name.
Notes: The configuration for HP Distributed Print Services and for text files) ...Manual on IBM AIX 4.x, use the name of the print server that you will need the HP UNIX Host Printing Software (part of queue to configure the printer. 11. To
do
this , you specified in that supports...
Troy Etherwind 802.11b Print Server Users Guide - Page 37
...services to be used nodename is the node name of the unit). 8
DEC LAT Network Configuration
Note: Only TROY EtherWind-N models include DEC LAT support....
S1 for the first serial port, P2 for the second parallel port, and S2 for the EIO, MIO, or first parallel port; For example:
$MCR LATCP CREATE PORT LTAxx:/APPLICATION SET... setup. The EtherWind wireless print ...
Troy Etherwind 802.11b Print Server Users Guide - Page 42
... not know this port is capable of the Ethernet address (the exact service names can be used
to know the service name, you do this, go the Start button, select Settings and then Printers. Select Add Printer to your E-mail server is used . - Service Name: Enter the service name on the screen.
10-2 You must now create...
Troy Etherwind 802.11b Print Server Users Guide - Page 50
... avoid problems caused by periods, defines the Ethernet address of the Server.
Boot Method This is the Service Set Identifier (Sometimes referred as Network Name or ESSID). For example, if a corporation has ...
The Data Rate usually does not need to manually set to 11 Mbps. The last position can be described by the other .
11-4 RF Channel The RF Channel is set automatically, ...
Troy Etherwind 802.11b Print Server Users Guide - Page 55
... is unable to answer your EtherWind.
They are familiar with your EtherWind, including telephone support, repair services, extended warranty, and advance replacement. Also, make sure that you have the serial number of this manual or the TROY site to isolate any problems and be able to provide you with your needs, and will generally be sure...
Troy Etherwind 802.11b Print Server Users Guide - Page 56
... purchase order. To ensure prompt service, please fill out the enclosed warranty card. DISCLAIMER OF WARRANTIES.
Make sure that you put this number on repaired products or replacement products is 30 days or the last day of the warranty of shipment if the Hardware is installed by the Technical Support Group (adequate insurance is not...
Oki OL840 Reviews
We have not received any reviews for Oki yet.