Oki MICROLINE 186 Plus - Parallel Support and Manuals
Get Help and Manuals for this Oki Data item
View All Support Options Below
Free Oki MICROLINE 186 Plus - Parallel manuals!
Problems with Oki MICROLINE 186 Plus - Parallel?
Ask a Question
Free Oki MICROLINE 186 Plus - Parallel manuals!
Problems with Oki MICROLINE 186 Plus - Parallel?
Ask a Question
Popular Oki MICROLINE 186 Plus - Parallel Manual Pages
Users Guide - Page 2
... by other companies does not necessarily constitute endorsement by Oki Data. Word Perfect is a registered trademark of errors or omissions beyond its control. Oki Data assumes no responsibility for the results of IBM Corporation.
Copyright 2017 by Oki Data. All Rights Reserved
Document: MICROLINE ML186 Plus User's Guide
First Edition: May, 2017
We invite you to -date...
Users Guide - Page 3
... Panel Operation 39 Setting Printer Defaults 42 Using the Pull Tractor Unit 51 Using the Roll Paper Stand 54 Maintenance 58 Replacing the Ribbon Cartridge 58 Testing Your Printer 60 Cleaning the Housing 62 Troubleshooting 64 General Information 64 Clearing Paper Jams 69 Parts & Options 78 Replacement Parts 78 Options 79 Specifications 80 Index 84 Oki contact details...
Users Guide - Page 11
... 0.28 mm] Forms, 4-part [maximum thickness 0.28 mm]
Lever Position 1 or 2 2 or 3 3 3
11 • Getting Started Adjusting the Head Gap
The head gap is the distance between the printhead and the platen roller. Incorrect setting of the head gap can cause printhead damage or ribbon jams. To avoid these problems set the head gap...
Users Guide - Page 30
... have a copy of each test printout contains information about your printer. Testing Your Printer
Your printer has a built-in test (self test) to call for service.
30 • Setting Up Your Printer Load continuous forms paper into the printer (see page 14, ff.). 2. Make sure the printer is...
Users Guide - Page 34
... m) • 25-pin serial connector. Serial Cable Requirements: • Shielded RS-232C cable, UL and CSA approved • Max.
3. Serial (COM) Connection, RS-232C Serial Model Only
Note
Interface cables are both turned OFF.
34 • Setting Up Your Printer
Users Guide - Page 36
... is selected in the printer menu. 1. Install the Windows Printer Driver
To print from a Windows-based system, install the printer driver located in the Drivers folder on -screen instructions to install the driver to be used
with your printer. Place the CD in your printer driver.
• Settings made in the printer driver normally override settings made in your CD-ROM drive...
Users Guide - Page 37
... make full use of the ML186 Plus printer's features, use of the printer's capabilities.
37 • Setting Up Your Printer Non-Windows Systems: Set the Emulation in the Printer Menu" below). the factory default • Epson® ESC/P2 • Oki Data® MICROLINE® Standard
If you are directly replacing a MICROLINE ML184 Turbo or ML184 printer...
Users Guide - Page 38
...Emulation Mode
IBM
5. The printer enters the menu mode.
4. Press TOF SET once or twice until the emulation you wish to change the menu default to...setting and exit the printer menu.
38 • Setting Up Your Printer ML186 Plus Emulation Mode IBM
Epson
ML
Compatible Printers/Drivers
IBM 2480 IBM Graphics Printer Plus IBM Graphics Printer
Epson ESC/P2 Epson LX Plus Epson LX
Okidata MICROLINE...
Users Guide - Page 60
Make sure the printer is set up and working correctly.
1. The test print begins. 3.
Be sure to have a copy of each test printout contains information about your printer. Note
The top ... LINE
FEED while turning the printer on. Testing Your Printer
Self Test (Font Samples)
Your printer has a built-in test (self test) to call for service.
60 • Maintenance
Users Guide - Page 65
...'t blown or that override the panel and menu settings. call for I turn on changing menu settings, see Note above). 2. To eliminate this problem, enter the Menu Mode, go to Yes.
Solution... code, enter the Menu Mode, go to the Parallel Interface group and change the setting for Reset Inhibit to the Set-Up group and change the setting for service.
65 • Troubleshooting For...
Users Guide - Page 66
... printer and the computer.
Solutions
The head gap could be sure that the printer driver you entered them correctly. Check that the interface cable is set correctly (see "Changing Menu Settings" on ? Solutions
1. Problem 5 Ink smears on page 11).
66 • Troubleshooting Is the SELECT light on page 45.
2. Check to print a document. If not...
Users Guide - Page 67
... not, replace the ribbon cartridge. Try moving the Head Gap Lever (1) to a lower setting. If that doesn't help, the printhead may not be damaged; Solution
The ribbon shield (1) is missing, find it, see if
you cannot find it and install it. If it is smeared and streaked. call for service.
67 • Troubleshooting If you...
Users Guide - Page 68
... still blinks, call for service.
Make sure the lever is in the printer menu can be used this option to cover the sensor groove. Problem 8 The ALARM light is paper installed. Problem 9 The Print Quality and Character Pitch keys on again. Check with your system manager before changing any menu settings. Solution
The most likely...
Users Guide - Page 85
......... 25-26, 28-29
Paper separator installing 12 replacement 78
Paper specifications 81
Parallel
computer connection ......33-34
interface menu settings ........ 50 PITCH button 41 PITCH lights 39 Platen knob 10
replacement 78 Power connection 13 Power cord
replacement 78 POWER light 39 Print speed 80 Printer
defaults 42 dimensions 82 drivers 36 reliability 81 weight 82 Printhead...
Users Guide - Page 87
... 76 54 21 50 (n° non surtaxé) Website: www.oki.fr
87 • Oki contact details Futurama Business Park Sokolovská 651/136D 186 00 Praha 8 Czech Republic
Tel: +420 224 890158 Fax: +420 22 232 6621 Website: www.oki.cz, www.oki.sk
Oki Systems (Deutschland) GmbH Hansaallee 187 40549 Düsseldorf
Tel: +49...
Oki MICROLINE 186 Plus - Parallel Reviews
We have not received any reviews for Oki yet.