Maytag MGD8100DW Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MGD8100DW manuals!
Problems with Maytag MGD8100DW?
Ask a Question
Free Maytag MGD8100DW manuals!
Problems with Maytag MGD8100DW?
Ask a Question
Most Recent Maytag MGD8100DW Questions
Steam Is Filling The Room
Steam is filling the room when running my new maytag mgd8100dw
Steam is filling the room when running my new maytag mgd8100dw
(Posted by Masmarto317 9 years ago)
Popular Maytag MGD8100DW Manual Pages
Use & Care Guide - Page 5
...Service calls caused by improper venting are not covered by the warranty and will reduce your drying times and improve your steam dryer (on some models...set and sometimes results in good air flow. n Use of fabric softener sheet is not recommended with heat, dryers require good air flow to follow the Installation Instructions...least every 2 years.
n Replace plastic or foil vent material
...
Use & Care Guide - Page 7
... garment label instructions. Wrinkle Prevent...minutes to manually reposition ...models), and Wrinkle Control (on some cycles, you may select a Dryness Level based on the type of periodic tumbling to select a cycle for 3 seconds to dry completely. Steam Boost can be enabled when recovering from a power failure. See "Cycle Guide" for use a preset temperature that sound when a feature, setting...
Use & Care Guide - Page 8
... than 1/4 full.
SENSOR CYCLES
Settings and options shown in the load or air temperature and shuts off when the load reaches the selected dryness level.
CYCLE GUIDE - Use Sensor Cycles for large...Saver
Cycle Details:
O ffers stepped drying starting with High and Medium Drying Temperature settings.
* On steam models only. Do not tightly pack. Medium load: Fill the dryer drum up to...
Use & Care Guide - Page 9
... dry:
Any load NOTE: Select Air Only to tumble freely.
9 CYCLE GUIDE -
TIMED CYCLES
Settings and options shown in the display. The maximum dry time is a power failure, settings will be used for use with High and Medium Drying Temperature settings.
* On steam models only. Load Size Recommendations For best results, follow the load size...
Use & Care Guide - Page 12
...dryer drum. See "Troubleshooting" section.
Done This ...12 Start the dryer. Not all indicators are other error issues during Timed Cycles or options such as Wrinkle ...vent system for the entire cycle. Rest the rear support on the front of the drying rack. CYCLE STATUS...model. 6.
Place wet items on top of the drying rack with the holes in the cycle by using the Air Only setting...
Use & Care Guide - Page 15
... or circuit breaker has tripped. Replace the fuses or reset the circuit breaker. If the problem continues, call . The drum may be louder and run
Possible Causes
Door not closed completely.
See the Installation Instructions. Separate the load items and restart the dryer. Reduce load size to possibly avoid a service call an electrician. Hold your...
Use & Care Guide - Page 16
.... Proper operation of the cycle. Lint on Sensor Cycles.
Change the dryness level setting on model) has been selected.
The load was tightly packed.
NOTE: Refer to the dryer.
The dryer is clogged with lint.
Level the dryer. See the Installation Instructions.
Select the Timed Dry cycle,
wet spots. Lint screen is not level...
Use & Care Guide - Page 17
... CONTROL LOCK for service. In Canada www.maytag.ca for details. Ventilate the area. before cooldown portion Allow the dryer to run when this diagnostic code is best for the type of lint and debris.
• C onfirm that the water supply is connected to possibly avoid a service call.
Refer to the Installation Instructions for assistance and...
Use & Care Guide - Page 18
..., operator, or installation instructions.
2. Please take a few minutes to review the Troubleshooting or Problem Solver section of surfaces resulting from defects in materials and workmanship and is intended for service in -home repair. 11. call 1-800-807-6777. If outside the 50 United States and Canada, contact your product from the date of repair or replacement under this...
Warranty Information - Page 1
... ask Maytag or your product. 3.
All warranty service is installed, operated, and maintained according to instructions attached to correct product damage or defects caused by the remaining term of the Use and Care Guide, scan the QR code on the below named parts only and does not include repair labor. call 1-800-807-6777. Consumable parts (i.e. Service or parts for service in...
Installation Guide - Page 7
... model/serial rating plate for use Power Supply Cord Replacement Part Number 8529008. For further information, please reference service numbers located in "Assistance or Service" section of your Use and Care Guide. This dryer is equipped with a cord having an equipmentgrounding conductor and a grounding plug. WARNING: Improper connection of the equipment- SAVE THESE INSTRUCTIONS
GROUNDING...
Installation Guide - Page 8
...Code, ANSI Z223.1. Dupont De Nemours and Company.
8 BURNER INPUT REQUIREMENTS Elevations above 2,000 ft. (610 m): ■■When installed above 2,000 ft. (610 m) a 4% reduction of the
burner Btu rating shown on the model...In Canada: An individual manual shut-off valve must be installed in elevation. For a garage installation, the gas pipe height must be installed within six (6) ft. ...
Installation Guide - Page 15
...extra part, go away. q Check for leaks around "Y" connector, faucet, and hoses.
Do not select Air Only Temperature setting. If dryer will not start, check the following instructions ...and T25 are for certain part replacement or repair.
Place the door on . q Check that the flexible gas line is not crushed or kinked.
This dryer automatically runs an installation diagnostic routine at the ...
Dimension Guide - Page 1
...39" Max. (990 mm)
Bottom view: Back view:
61/4" (159 mm)
Recommended Installation Spacing:
53/4"* (146 mm)
Water inlet
(Steam Models Only)
Vent
297/8"* (759 mm)
31/2"* (89 mm)
Gas
3/4"* (18 mm)... closet installation, with a door, minimum ventilation openings in .2 min. (155 cm2) 3" (76 mm)
1" (25 mm)
1" (25 mm)
NOTE: Most installations require a minimum of installation and servicing.
&#...
Dimension Guide - Page 2
... is required. For complete details, see Installation Instructions packed with the National Fuel Gas Code ANSI Z223.1. gas must be used . An individual manual shutoff valve must be used . ELECTRICAL ... the gas supplier and local codes, 3/8" approved tubing may be converted to change materials and specifications without notice.
WATER (STEAM MODELS ONLY) REQUIREMENTS
The dryer must...
Maytag MGD8100DW Reviews
We have not received any reviews for Maytag yet.