Maytag MGD7000AG Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MGD7000AG manuals!
Problems with Maytag MGD7000AG?
Ask a Question
Free Maytag MGD7000AG manuals!
Problems with Maytag MGD7000AG?
Ask a Question
Most Recent Maytag MGD7000AG Questions
What Side Does Door Open On When Delivered? Mgd7000
(Posted by Woodyluvs03 10 years ago)
Maytag MGD7000AG Videos
Maytag MGD7000AG Front Load Dryer
Duration: :58
Total Views: 14
Duration: :58
Total Views: 14
Popular Maytag MGD7000AG Manual Pages
Warranty Information - Page 1
... Phone number Model number Serial number Purchase date
18
Consumable parts are unable to resolve
the problem after checking "Troubleshooting," additional help you obtain assistance or service if you should ask Maytag or your retailer about buying an extended warranty. Repairs to parts or systems resulting from unauthorized modifications made to repair or replace appliance light...
Dimension Guide - Page 1
..." (686 mm)
381/8" (968 mm)
Gas Dryer
Side view:
3/4"* (18 mm)
Back view:
61/4" (159 mm)
Recommended Installation Spacing:
Water inlet
(Steam Models Only)
53/4"* (146 mm)
Vent
297/8"* (759 mm)
31/2"* (89 mm)
Gas
3/4"* (18 mm)
143/8" (365 mm...Companion appliance spacing should be considered for ease of installation and servicing. ■■ Additional clearances might be considered.
Dimension Guide - Page 2
...right to the gas supplier and local codes, 3/8" approved tubing may be installed within 6 ft (1.8 m) of ...Installation Instructions packed with Natural gas. To determine maximum exhaust length, add one 90º turn inside the dryer. An individual manual...coupling can be connected to change materials and specifications without notice.
VENTING REQUIREMENTS
Exhaust venting: ...
Installation Guide - Page 4
...;Vent elbows and vent work
Parts needed (steam models):
Utility knife
Tin snips (new vent installations)
2' (0.6 m) inlet hose
5' (1.52 m) inlet hose and rubber washer
Caulking gun and compound Adjustable wrench that all models):
Flat-blade screwdriver
#2 Phillips screwdriver
Leveling legs (4) Parts supplied (steam models):
1/4" and 5/16" nut driver (recommended)
Level
Tape measure...
Installation Guide - Page 5
...Part Number 279810. LOCATION REQUIREMENTS
DRYER DIMENSIONS Front view:
27" (686 mm)
381/8" (968 mm)
You will need 18" (460 mm) to bottom of dryer.
■■The dryer must support dryer weight of 200 lbs. (90.7 kg). IMPORTANT: Do not operate, install...
measurement
61/4" (159 mm)
53/4"* (146 mm)
Vent
Water inlet
(Steam Models Only)
297/8"* (759 mm)
31/2"* (89 mm)
Gas
3/4"* (18 mm)...
Installation Guide - Page 6
...from
your "Use and Care Guide". Mobile home - Additional installation requirements: This dryer is equipped with a door, minimum ventilation openings in garages, closets, mobile homes, or sleeping quarters. Check code requirements. Some codes limit, or do not permit, installation of the dryer in the top and bottom of installation and servicing.
■■Additional clearances might...
Installation Guide - Page 7
... your dryer. Check with all local codes and ordinances. Do not use an extension cord. amp fused electrical supply is also recommended that is properly installed and grounded in accordance with a quali ed electrician or service representative or personnel if you use Power Supply Cord Replacement Part Number 8529008. GROUNDING INSTRUCTIONS
I For a grounded, cord-connected dryer...
Installation Guide - Page 8
... m) a 4% reduction of the
burner Btu rating shown on the model/serial number plate is recommended that an individual manual shutoff valve be easy to reach for each 1,000 ft. (305 m) increase in accordance with the B149.1, Natural Gas and Propane Installation Code.
The location should be installed within six (6) ft. (1.8 m) of E.I.
D
B
A. 3/8" flexible gas connector B. 3/8" pipe...
Installation Guide - Page 9
INSTALL LEVELING LEGS
MAKE GAS CONNECTION (gas models only)
1. place under each of LP gas Do not use a large flat piece of pipe fittings must use a wrench to existing gas line. Non-flared ...
Installation Guide - Page 10
...)
■■ Must be fully extended and supported in final dryer location.
■■ Remove ... airflow and poor performance.
■■ Do not install in enclosed walls, ceilings, or floors.
■■... performance.
Review "Vent System Chart" and if necessary, modify existing vent system to seal all governing codes and ordinances...Replace plastic or metal foil vents with lint.
Installation Guide - Page 15
q Check for certain part replacement or repair. See "Level Dryer".
Do not select Air Only Temperature setting. This dryer automatically runs an installation diagnostic routine at the start dryer.... dust. Electric Models
q Plug into a grounded outlet. q Check to the need for leaks around "Y" connector, faucet, and hoses.
q If you have all of your "Use and Care Guide". The odor ...
Installation Guide - Page 16
...; T25 screwdriver, remove the 2 screws securing the door strike to the door frame of the door facing up and off the inner door and set aside (B).
B
Using a Phillips screwdriver, remove the 2 screws from outer door
Fig. A
Fig. Using a Phillips screwdriver, remove the 10....
3. Rotate the strike 180° and attach to the outer door. 2. Lift off the trim ring and set aside.
16
Installation Guide - Page 19
... of dryer door frame, as shown.
double handle
1. Place the door on a soft towel or other non-scratch surface. Lift off the inner door and set aside.
4. Hinge
Using a TORX T25 screwdriver, remove the 3 TORX screws securing the latch plate and latch backing plate and the 5 screws holding the hinge assembly...
Installation Guide - Page 20
... facing up and out to the dryer and lift up .
Reinstall the 10 screws securing the inner door to engage the top tab. Retain or set aside the 4 screws.
20 R einstall hinge and latch on a soft towel or other non-scratch surface. Secure in place with the inside of door
Using...
Installation Guide - Page 21
... a small release tab on each side of the door facing up. Lift off the inner door and set aside for later use.
Move the door strike
4. Remove hinge and latch
from
outer door
Release tab...sides from which they were removed.
21 2. Remove the 4 screws above and below the door strike and set aside. If the inner and outer door do not separate easily, slide a credit card, putty knife,...
Maytag MGD7000AG Reviews
We have not received any reviews for Maytag yet.