Maytag MGD6630H Support and Manuals
Get Help and Manuals for this Maytag item
This item is in your list!
View All Support Options Below
Free Maytag MGD6630H manuals!
Problems with Maytag MGD6630H?
Ask a Question
Free Maytag MGD6630H manuals!
Problems with Maytag MGD6630H?
Ask a Question
Popular Maytag MGD6630H Manual Pages
Installation Instructions - Page 4
...
Utility knife
Tin snips (new vent installations)
Leveling legs (4) Parts needed (steam models):
"Y" connector
2' (0.6 m) inlet hose
Caulking gun and compound (new vent installations)
Adjustable wrench that opens to propane gas
Parts supplied (all parts are included. NOTE: Do not use leveling legs supplied with dryer if installing with dryer): ■■ Vent clamps ■■...
Installation Instructions - Page 5
....7 kg). Maytag® Models
IMPORTANT: Do not operate, install, or store dryer where it will be exposed to bottom of automatic sensor cycles, resulting in garages, closets, mobile homes, or sleeping quarters. The wires that connect to water and/or weather.
See "Venting Requirements."
■■ A separate 15 or 20 A circuit for a gas dryer or 30...
Installation Instructions - Page 6
..., and gas line.
■■ Additional spacing should be kinked. For further information, see "Assistance or Service" in your Use and Care Guide.
6 Installation Clearances For each arrangement, consider allowing more space for ease of the dryer in door are required. If a closet door or louvered door is available to reduce noise transfer. Some codes limit...
Installation Instructions - Page 8
... Power Supply Cord Replacement Part Number 8529008.
4-wire receptacle (14-30R)
For further information, please reference service numbers located in doubt as to whether the dryer is 5 ft. (1.52 m) long. Do not modify the plug provided with all local codes and ordinances. A copy of your responsibility:
■■ To contact a qualified electrical installer.
■■ To...
Installation Instructions - Page 9
... does not agree with the National Fuel Gas Code, ANSI Z223.1. The location should be easy to reach for use with appropriate conversion. ■■ Your dryer must be installed in
your dryer to connect your home. In Canada: An individual manual shut-off valve be made by the American Gas Association or CSA International) to the...
Installation Instructions - Page 17
...no kinks. Correct any leak found.
17 MAKE GAS CONNECTION
(Gas models only)
WARNING
2. A. 3/8" flexible gas connector B. 3/8" dryer gas pipe
C. 3/8" to 3/8" pipe elbow D. 3/8" pipe-to action of a qualified person include: licensed heating personnel, authorized gas company personnel, and authorized service personnel. Connect gas supply to dryer. valve is open when handle is shown. Securely...
Installation Instructions - Page 23
... part replacement or repair. Be sure vent is not crushed or
kinked.
Check that all packaging materials. Be sure the water faucets are snug against the floor and the dryer does not rock. All Models:
Select a Timed Dry heated cycle and start , check the following:
• Controls are now installed...
Quick Reference Sheet - Page 1
... new settings will illuminate when controls are other error
issues during
The key icon will be unable to remove a load immediately, touch Wrinkle Prevent to the online "Troubleshooting" section for details.
Online Ordering Information
For detailed installation instruction and maintenance information, winter storage, and transportation tips, please see the Owner's Manual included with...
Owners Manual - Page 3
...'s instructions and local codes. − Do not install a clothes dryer with clothes dryers. WARNING FIRE HAZARD Failure to follow safety warnings exactly could result in serious injury, death, or property damage. − Do not store or use gasoline or other flammable vapors and liquids in the vicinity of a specific type identified by a qualified installer, service agency, or the gas...
Owners Manual - Page 8
...purchased your dryer.
Parts Needed (steam models):
Caulking gun and compound (new vent installations)
Adjustable wrench that all models):
Pliers or slip-joint pliers
Tape measure
Utility knife
Tin snips (new vent installations)
Leveling legs (4) (Length and appearance of legs may be required, depending on your Quick Start Guide for contact and ordering information. Check local codes...
Owners Manual - Page 9
... for straight-back venting only. Installing on all sides of the dryer. IMPORTANT: Do not operate your washer's water supply by utilizing the necessary parts noted in the "Gas Dryer Power Hookup" section. � A sturdy floor to reduce noise transfer. Lower temperatures may cause dryer not to fully open. For steam models only, inlet hose must be...
Owners Manual - Page 10
... outlet that a separate circuit serving only this information does not agree with natural gas. It is located on the model/serial rating plate for electric current. WARNING: Improper connection of your dryer to connect your dryer. SAVE THESE INSTRUCTIONS
Explosion Hazard
Use a new CSA International approved gas supply line.
Do not use a new flexible stainless steel...
Owners Manual - Page 12
..., please reference the Quick Start Guide.
2. U.S.A. If connected to dryer. Recommended connection is used to connect dryer to action of all gas connections. Remove red cap from gas pipe.
Do not use PTFE plumber's tape.
12 Then, test all connections by brushing on threads of propane gas. Bubbles will show a leak. Install a shut-off valve. Open shutoff...
Owners Manual - Page 13
...Guide. A. Flexible metal vent (acceptable only if accessible to clean):
� Must be fully extended and supported in final dryer... cap the vent to seal all governing codes and ordinances. Replace plastic or metal foil vents with screws ...Vent System
Recommended exhaust installations:
Typical installations vent the dryer from ground or any object that extend into any gas vent, chimney, ...
Maytag MGD6630H Reviews
Do you have an experience with the Maytag MGD6630H that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Maytag yet.
Earn 750 points for your review!