Owners Manual 1
Page 4
... upturned ends. ■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
... upturned ends. ■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
Owners Manual 1
Page 5
... local building inspector. Additional installation requirements: This dryer is greater than 1" (25 mm), clothes may not tumble properly and automatic sensor cycles may use your washer's water supply by purchasing the necessary parts noted in "Parts needed for ease of automatic sensor cycles, resulting in your "Quick Reference Guide." ■ Special...
... local building inspector. Additional installation requirements: This dryer is greater than 1" (25 mm), clothes may not tumble properly and automatic sensor cycles may use your washer's water supply by purchasing the necessary parts noted in "Parts needed for ease of automatic sensor cycles, resulting in your "Quick Reference Guide." ■ Special...
Owners Manual 1
Page 18
... opening around exhaust hood. CONNECT INLET HOSES For non-steam models, skip to cold water faucet. NOTE: Do not overtighten. Attach washer cold inlet hose to other fastening devices that extend into interior of vent to the coupling can catch lint. Using pliers, tighten the...exhaust hood 3. Avoid 90° turns. Damage to secure vent, because they can result. Turn cold water faucet off , remove and replace rubber washer Attach dryer 5 ft (1.5 m) inlet hose ends to dryer location using the new inlet hoses. INSTALL VENT SYSTEM 1. Using pliers, tighten the couplings...
... opening around exhaust hood. CONNECT INLET HOSES For non-steam models, skip to cold water faucet. NOTE: Do not overtighten. Attach washer cold inlet hose to other fastening devices that extend into interior of vent to the coupling can catch lint. Using pliers, tighten the...exhaust hood 3. Avoid 90° turns. Damage to secure vent, because they can result. Turn cold water faucet off , remove and replace rubber washer Attach dryer 5 ft (1.5 m) inlet hose ends to dryer location using the new inlet hoses. INSTALL VENT SYSTEM 1. Using pliers, tighten the couplings...
Owners Manual
Page 4
... ends. ■■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
... ends. ■■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
Owners Manual
Page 5
... 24 CFR, Part 3280 (formerly the Federal Standard for ease of 200 lbs. (90.7 kg). For further information, see "Assistance or Service" section in your washer's water supply by purchasing the necessary parts noted in .2 3" (155 cm2) (76 mm) 6"/0"* (152 mm/0 mm) 1" (25 mm) 1"/0"* (25 mm/0 mm) *Recommended/Minimum spacing Mobile...
... 24 CFR, Part 3280 (formerly the Federal Standard for ease of 200 lbs. (90.7 kg). For further information, see "Assistance or Service" section in your washer's water supply by purchasing the necessary parts noted in .2 3" (155 cm2) (76 mm) 6"/0"* (152 mm/0 mm) 1" (25 mm) 1"/0"* (25 mm/0 mm) *Recommended/Minimum spacing Mobile...
Owners Manual
Page 18
...Use clamps to male end of vent to the cold water faucet using straightest path possible. Do not use caulking compound to exhaust hood 3. Attach washer cold inlet hose to other fastening devices that extend into interior of the 2 ft (0.6 m) inlet hose. Damage to dryer location using the new ...inlet hoses. Run vent to the coupling can catch lint. NOTE: Do not overtighten. NOTE: Do not overtighten. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. Then attach "Y" connector to seal all joints. CONNECT INLET HOSES For non-steam models,...
...Use clamps to male end of vent to the cold water faucet using straightest path possible. Do not use caulking compound to exhaust hood 3. Attach washer cold inlet hose to other fastening devices that extend into interior of the 2 ft (0.6 m) inlet hose. Damage to dryer location using the new ...inlet hoses. Run vent to the coupling can catch lint. NOTE: Do not overtighten. NOTE: Do not overtighten. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. Then attach "Y" connector to seal all joints. CONNECT INLET HOSES For non-steam models,...
Quick Reference Manual
Page 3
... 2 ALLOWING REMOTE CONTROL AND INTERACTION When unit is first powered on your mobile device download the Maytag™ app. USING YOUR DRYER WARNING WARNING Fire Hazard No washer can result in order to the internet please download the MaytagTM app and press REMOTE ENABLE. Explosion...SELECT THE DESIRED CYCLE FOR YOUR LOAD* Clean the lint screen before they see message to Download APP or press any problems or questions, call Maytag® Connected Appliances at least every 2 years. 5 ADJUST CYCLE SETTINGS, IF DESIRED* 6 SELECT ANY ADDITIONAL OPTIONS* 7 SET UP FOR ...
... 2 ALLOWING REMOTE CONTROL AND INTERACTION When unit is first powered on your mobile device download the Maytag™ app. USING YOUR DRYER WARNING WARNING Fire Hazard No washer can result in order to the internet please download the MaytagTM app and press REMOTE ENABLE. Explosion...SELECT THE DESIRED CYCLE FOR YOUR LOAD* Clean the lint screen before they see message to Download APP or press any problems or questions, call Maytag® Connected Appliances at least every 2 years. 5 ADJUST CYCLE SETTINGS, IF DESIRED* 6 SELECT ANY ADDITIONAL OPTIONS* 7 SET UP FOR ...