Makita XWT15T Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XWT15T manuals!
Problems with Makita XWT15T?
Ask a Question
Free Makita XWT15T manuals!
Problems with Makita XWT15T?
Ask a Question
Popular Makita XWT15T Manual Pages
XWT14 XWT15 Instruction Manual - Page 2
... may differ depending on your body is an increased risk of the battery cartridges and chargers listed above .
There is earthed or grounded.
3. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
XWT14
XWT15
Fastening capacities
Standard bolt
M10 - Never modify the plug in explosive atmospheres, such as pipes, radiators, ranges and refrigerators. WARNING: Only use any...
XWT14 XWT15 Instruction Manual - Page 3
...tool that have the power tool repaired before connecting to become complacent and... If contact accidentally occurs, flush with specifically designated battery packs.
Damaged or entangled ...battery pack, if detachable, from moving parts, breakage of dust collection can be ... Recharge only with the power tool or these instructions to protect your finger on invites accidents.
4. ...
XWT14 XWT15 Instruction Manual - Page 4
... this instruction manual may ...Installing the batteries to fire or temperature above 130 °C may be performed by third parties, forwarding agents, special requirement on (1) battery charger, (2) battery, and (3) product using only identical replacement parts. Follow all instructions and cautionary markings on packaging and labeling must be sure you have a firm footing. Never service...
XWT14 XWT15 Instruction Manual - Page 5
... 40 °C (50 °F - 104 °F). SAVE THESE INSTRUCTIONS.
If you notice less tool power.
2. CAUTION: Do not install the battery cartridge forcibly. In this situation, remove the battery from the ...become overloaded. Tips for a few seconds.
5 ENGLISH Overcharging shortens the battery service life.
3. Let a hot battery cartridge cool down before turning the tool on the upper side...
XWT14 XWT15 Instruction Manual - Page 6
... the switch trigger, the lamp status can be changed .
6 ENGLISH Switch trigger
CAUTION: Before installing the battery cartridge into the tool, always check to see the source of light directly.
1 ... conditions of use and the ambient temperature, the indication may have the tool serviced at a Makita service center. The lamp goes out approximately 10 seconds after the switch trigger is...
XWT14 XWT15 Instruction Manual - Page 7
... A side for clockwise rotation or from the B side for counterclockwise rotation. Changing the direction of rotation before operation. CAUTION: When not operating the tool, always set the reversing switch lever to a complete stop. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled.
7 ENGLISH This...
XWT14 XWT15 Instruction Manual - Page 10
... type of the square drive on the switch panel go out when the tool is aligned with the ring spring
Model XWT14
For impact socket without O-ring and pin
1
2
1
2 3
► 1 . Lamp
When full... comes out, do not pull the switch trigger fully. To remove the impact socket, follow the installation procedures in the impact socket groove to the bolt or nut. When full speed mode is firmly ...
XWT14 XWT15 Instruction Manual - Page 11
... it locks in place. Impact socket 2. Tap it off from the tool and result in the figures. To install the hook, insert it into place. If you .
► 1 . If not, the hook may differ...the tool, causing injury to you or someone around you can be installed on the upper side of the impact socket with the detent pin
Model XWT15
1 2 3
4
OPERATION
CAUTION: Always insert the battery ...
XWT14 XWT15 Instruction Manual - Page 12
...manual. Only use of any assistance for the most current warranty terms applicable to persons.
Fastening torque
NOTE: Hold the tool pointed straight at low speed will differ according to be fastened will be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts... available, refer to the warranty details set forth at below website for use the...
XWT15T New Tool Flyers English - Page 1
... N•m Overall Length 5-5/8" UPC Code (XWT15T 088381-898126 UPC Code (XWT15Z 088381-898096
STANDARD EQUIPMENT
...Set (A-96372) 2. 18V LXT® Lithium-Ion Compact 2.0Ah Battery (BL1820B) 3. 18V LXT® Lithium-Ion 6.0Ah Battery (BL1860B) 4. 18V LXT® Brushless 4-Speed Impact Driver (XDT16Z) 5. 18V LXT® Brushless 1/2" Hammer Driver-Drill (XPH07Z)
1
2
3
4
5
All specifications...
Makita XWT15T Reviews
Do you have an experience with the Makita XWT15T that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!