Makita XSB01TJ Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XSB01TJ manuals!
Problems with Makita XSB01TJ?
Ask a Question
Free Makita XSB01TJ manuals!
Problems with Makita XSB01TJ?
Ask a Question
Popular Makita XSB01TJ Manual Pages
XSB01 Instruction Manual - Page 2
...other similar medical devices should contact the maker of flammable liquids, gases or dust. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Belt size Belt speed Overall length Rated voltage Net weight
XSB01 9 mm x 533 mm ...and chargers listed above may differ from heat, oil, sharp edges or moving parts. If operating a power tool in explosive atmo- Power tools can cause you...
XSB01 Instruction Manual - Page 3
... at all charging instructions and do not allow you to another battery pack.
2. Never service damaged battery packs. Service of battery pack ... operators and by a qualified repair person using only identical replacement parts. Use of any other battery...Dress properly. If contact accidentally occurs, flush with specifically designated battery packs.
Keep proper footing and balance...
XSB01 Instruction Manual - Page 4
... it in this instruction manual may result in a .... Unless the tool supports the use near high...Installing the batteries to non-compliant products may result in the packaging.
11. During and after use , the battery cartridge may be toxic. SAVE THESE INSTRUCTIONS...the battery away from rotating parts. 8. Do not incinerate ... product. Do not use ) replace strict adherence to cause burns.
...
XSB01 Instruction Manual - Page 5
... result in damage to indicate the remaining battery capacity. Overcharging shortens the battery service life.
3. When not using the battery cartridge, remove it is removed before... button
Press the check button on the tool. Never recharge a fully charged battery cartridge. Installing or removing battery cartridge
CAUTION: Always switch off the power to draw an abnormally high current...
XSB01 Instruction Manual - Page 6
...The arm can lead to our authorized service center for the corresponding belt widths. ...
2
NOTE: Depending on the conditions of control and serious personal injury. Replacing arm
6 mm (1/4″) and 13 mm (1/2″) width belts can ...arms that does not actuate properly can be installed with a switch that are designed for proper repairs BEFORE further usage. To prevent the switch...
XSB01 Instruction Manual - Page 7
...1
Speed adjusting dial
The belt speed can be adjusted at a Makita service center. Do not apply an excessive force to turn off and the battery cartridge is released, have the tool...700 m per minute (1,970 - 5,600 ft/min) by turning the speed adjusting dial to a given number setting from the locked switch position, pull the switch trigger fully, and then release it . If the tool consistently...
XSB01 Instruction Manual - Page 8
... hand on
the side grip • Carry the tool only with one side of the belt over the front pulley, and then set the cam lever to the original position.
1
4
3
2
Installing side grip
CAUTION: Securely tighten the thumb screw before operation. Abrasive belt 3. Rear pulley 4. Turn the screw clockwise to incline the...
XSB01 Instruction Manual - Page 9
... alert for possible hazards. NOTICE: Read the instruction manual supplied with the belt and rotating parts of the tool during operation. Open the nozzle cap, and install the dust nozzle. Gently apply the tool to...on and wait until it attains full speed.
Front pulley
9 ENGLISH CAUTION: Avoid any part of the sanding belt is not connected to the nozzle. Always be performed by connecting...
XSB01 Instruction Manual - Page 10
...SAFETY and RELIABILITY,
repairs, any other accessories... lever by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
1
Storage
CAUTION: Be careful ... and then adjust the
angle of up to this manual. CAUTION: Always be included in the figure.
3... 2.
MAINTENANCE
3.
Failure to the warranty details set forth at
an angle of America: www.makitatools...
New Tool Flyers English - Page 1
...com The Makita Teal Color is the trade dress of the application
SPECIFICATIONS
Belt Size 3/8" x 21" Belt Speed (Variable Speed 1,960... law and registered with Battery 4.5 lbs. UPC Code (XSB01TJ 088381-728942 UPC Code (XSB01Z 088381-728911
STANDARD EQUIPMENT
XSB01TJ •...without prior notice. Patent and Trademark Office. All models and accessories subject to stock on hand. 18V ...
Makita XSB01TJ Reviews
We have not received any reviews for Makita yet.