Makita XPT02Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XPT02Z manuals!
Problems with Makita XPT02Z?
Ask a Question
Free Makita XPT02Z manuals!
Problems with Makita XPT02Z?
Ask a Question
Popular Makita XPT02Z Manual Pages
XPT02 Instruction Manual - Page 2
.... ENGLISH (Original instructions)
SPECIFICATIONS
Model
XPT02
Impact driver mode
Fastening Capacities
...(1/8") max.)
No load speed (/min) Depends on torque
(Low (1) / High (2))
setting
0 - 300 / 0 - 1,100
P mode
0 - 600 / 0 - ...specifications herein are subject to change without notice. • Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts...
XPT02 Instruction Manual - Page 3
... your power tool serviced by poorly maintained ...repair person using only identical replacement parts. Do not use the power tool if the switch does not turn it was designed.
2. CORDLESS 4 MODE IMPACT DRIVER...repaired before connecting to power source and/or battery pack, picking up or carrying the tool. in the instructions.
Use auxiliary handle(s), if supplied with specifically...
XPT02 Instruction Manual - Page 4
...INSTRUCTIONS. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service...instructions and cautionary markings on packaging and labeling must be sure you do not use ) replace...parts. 8. Do not disassemble battery cartridge. 3. Do not use genuine Makita batteries. For preparation of blow
Important safety instructions for the Makita...this instruction manual may...
XPT02 Instruction Manual - Page 5
...seconds.
5 ENGLISH Red indicator 2. The indicator lamps light up for battery cartridges with star marking.
1
3
► 1 .
Installing or removing battery cartridge
1 2
Overload protection
When the battery is overheated, the tool stops automatically. Then turn the tool off your...button on the upper side of the button, it is placed under one of the model number.)
1
2
► 1 .
XPT02 Instruction Manual - Page 6
... switch trigger actuates properly and returns to see the source of use and the
ambient temperature, the indication may have tool serviced at a Makita service center.
► 1 . Switch trigger
CAUTION: • Before installing the battery cartridge into the
tool, always check to the "OFF" position when released. When the lamp does not come on...
XPT02 Instruction Manual - Page 7
.... If the ring does not easily move, pull the switch trigger slightly to the neutral position. When turning the action mode changing ring to impact driver mode, set the reversing switch lever to rotate the spindle and then move the ring. • In the hammer drill mode or drill mode, the blowing...
XPT02 Instruction Manual - Page 8
...driver mode)
1 2
5
3
4
► 1 . Soft
Tightening when excessive
1,200 (/min)
tightening need to be avoided Tightening sash screw/ because of switch trigger, the impact force grade cannot be changed.
8
Changing the torque setting...force can be changed in three steps. The indication "P" is pressed, the torque setting changes from 1 to 9 and P, and then returns to the work. Every time...
XPT02 Instruction Manual - Page 9
..., contact your material or a piece of torque setting does not mean specific torque rate. Empty signal for a particular application. Installing or removing driver/drill/ socket bit
1
► 1 . Do not use any work on P mode. • With speed change lever at "2" side, fastening max. 4 mm screw into your nearest Makita service center. • When the remaining battery...
XPT02 Instruction Manual - Page 10
...-piece 3.
Groove 2. The hook is not necessary. OPERATION
1 2 3
► 1 .
Replace the drill bit after operating
as it will go . Hook (Optional accessory)
1
1
2
► 1 . This can be installed on either side of bits, follow B=14mm the procedure (1). Then release the sleeve to the instructions above. • After inserting the bit, make sure that it...
XPT02 Instruction Manual - Page 11
...following. If the tool does not work properly, contact your nearest Makita service center.
• Hold the tool pointed straight at the screw... the tool to the extent that the screw is set to rest for 15 minutes before operation. After fastening...
2. Install it fully until it is operated continuously until the battery cartridge has discharged, allow the tool to impact driver mode,...
XPT02 Instruction Manual - Page 12
...twist your bit, decrease the tool performance and shorten the service life of the tool. • There is locked.... results. Drilling
over the following chart for the work .
• Make sure that the driver bit is a tremendous and sudden twisting force exerted on LED Display 1
3
5
7
... will be drilled dry. The guide screw makes drilling easier by setting the reversing switch to prevent the...
XPT02 Instruction Manual - Page 13
... by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty gives you specific legal rights, and you need any other rights which vary from country to country. Should any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. This Warranty does not...
XPT02 Parts Breakdown - Page 3
Model XPT02Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part...-0
042
326126-3
043
234233-7
044
216011-7
HOUSING SET RUBBER PIN 6 INC. 15 XPT02 NAME PLATE TAPPING... CUP WASHER HAMMER CHANGE PLATE HAMMER CHANGE RING COMPRESSION SPRING 2 CHANGE CASE GEAR CASE ASS'Y PIN GUIDE FLAT FILLISTER HD. PIN 1.2-3.5 NYLON WASHER 15 O RING 12.5 STEEL BALL 3.5 ANVIL M COMPRESSION ...
XPT02Z New Tool Flyers English - Page 1
...174; Lithium-Ion 5.0Ah Battery (BL1850B)
2
3
4
5
All specifications subject to stock on hand. ImpactX™ 50 Pc. All models and accessories subject to change without prior notice. Patent and Trademark Office. Driver Bit Set (A-98348)
1
2. 5 Pc. Shipping Weight 3.31 lbs. The Makita Teal Color is the trade dress of Makita Corporation and is electronically controlled to...
Makita XPT02Z Reviews
We have not received any reviews for Makita yet.