Makita XPK01Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XPK01Z manuals!
Problems with Makita XPK01Z?
Ask a Question
Free Makita XPK01Z manuals!
Problems with Makita XPK01Z?
Ask a Question
Popular Makita XPK01Z Manual Pages
XPK01Z Instruction Manual - Page 2
...increase the risk of flammable liquids, gases or dust.
The term "power tool" in electric shock... Work area safety 1. Personal safety 10. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XPK01
Planing width
82 mm (3-1/4")
Planing depth
2 mm ... to lose control.
Distractions can cause you to a rotating part of electric shock if your mains-operated (corded) power tool...
XPK01Z Instruction Manual - Page 3
... and grease. Use of any adjusting. 13. Holding the work by a qualified
repair person using the tool on . 11. Handle the blades very carefully.
6. Use the correct
power tool for a while. Before using only identical replacement parts. Keep your power tool serviced by your hand or against the body leaves it run for your finger...
XPK01Z Instruction Manual - Page 4
... from repeated use the correct dust mask/respirator for a long ...service life.
3. Do not incinerate the battery cartridge even if it .
4. Follow your eyesight. 5. Charge the battery cartridge once in this instruction manual may reach or exceed 50 ﾟ C (122 ﾟ F). 7. Always change both blades...) replace strict adherence
to drop or strike battery. 9. SAVE THESE INSTRUCTIONS. ...
XPK01Z Instruction Manual - Page 5
... tool while sliding the button on the tool. CAUTION: • Always install the battery cartridge fully until it all the way until the
red indicator cannot... completely. If you . • Do not install the battery cartridge forcibly. Switch trigger
011738
CAUTION: • Before installing the battery cartridge into place. To install the battery cartridge, align the tongue on the...
XPK01Z Instruction Manual - Page 6
...blade, if the tool has been in the blade groove and the heel
of the gauge plate.
3. Planer blade
locating lugs
4. To install the blades, loosely attach the adjusting
plate to remove or install the blades. Return tool a MAKITA service center for proper repairs... hands when removing or installing the blades. • Use only the Makita wrench provided to the set plate with lock-off
...
XPK01Z Instruction Manual - Page 7
... and the tool body.
9. Blade edge
3. Installing conventional planer blade (optional accessory)
To install the blades, first clean out all the installation bolts evenly and alternately with the
socket wrench provided) and hand rotate the
drum to check clearances between the drum and the set
plate to be positioned by the planer blade
locating lugs on the other.
8. Bolts...
XPK01Z Instruction Manual - Page 8
... install the nozzle (optional accessory). For tool with nozzle Attach the dust bag onto the nozzle.
Cause: One or both blade edges
(B)
fails to protrude enough in
relation to rear base line. For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is tapered. Nozzle 2. NOTE: • If you connect a Makita...
XPK01Z Instruction Manual - Page 9
... shown in the figure, use the edge fence (guide rule) which is obtained as shown in the figures...Makita vacuum cleaner to your tool. Cutting line
2 1
011752
9 End
011757
For tool without nozzle
Remove the chip cover and install the nozzle (optional accessory...on and wait until the blades attain full speed. Planing operation
1
1. Elbow (optional accessory)
1. For tool without nozzle...
XPK01Z Instruction Manual - Page 10
...of the workpiece and plane it.
Sharpening holder
1
002588
Always keep your blades sharp for attaching an extension guide (optional accessory).
011748
To make a chamfering cut as shown in the figure, align...flush with the edge of the tool. Screw 2. Edge fence
(optional accessory) 2 1
Chamfering
011760
Adjust the edge fence until it by attaching an extra piece of...
XPK01Z Instruction Manual - Page 11
... sides (C) and (D).
If you need any other maintenance or adjustment should be
performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts. Screwdriver
002590
Immerse the dressing stone in water for more details regarding these accessories, ask your Makita tool specified in the holders. Hold the holder so that they wear down to the...
XPK01Z Instruction Manual - Page 12
... OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. • Blade gauge • Set plates set • Edge fence (Guide rule) • Extension guide set • Dressing stone • Nozzle • Dust bag assembly • Elbow • Socket wrench • Plastic carrying case • Makita genuine battery and charger
NOTE: •...
XPK01Z Parts Breakdown - Page 2
Model XPK01Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
Q'ty Unit
001
266326-2 ...
041
452478-7 BELT COVER
042
911128-8 PAN HEAD SCREW M4X16
043
222173-1 V-PULLEY 4-33.5
044
211088-7 BALL BEARING 6000DDW
6 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 SET 2 PC. 1 PC. 1 PC. 1 PC. 1 1 PC. 1 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 ...
XPK01Z Parts Breakdown - Page 3
... C20 411086-3 GAUGE PLATE
A04
782209-3 SOCKET WRENCH 9
1 PC. 1 PC. 1 SET 2 PC. 2 PC. 4 PC. 1 SET 6 PC. 1 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. MINI PLANER BLADE
048
343433-9 SET PLATE F/MINI BLADE
049
345644-2 ADJUST PLATE
050
265132-2 + PAN HEAD SCREW M4X5
051
187679-5 DRUM PLATE SET
052
251609-3 HEX. 045
161061-6 DRUM
046
211032-4 BALL BEARING 608ZZ...
Makita XPK01Z Reviews
We have not received any reviews for Makita yet.