Makita XKH01Z Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XKH01Z manuals!
Problems with Makita XKH01Z?
Ask a Question
Free Makita XKH01Z manuals!
Problems with Makita XKH01Z?
Ask a Question
Popular Makita XKH01Z Manual Pages
XKH01 Instruction Manual - Page 2
...Specifications may differ from heat, oil, sharp edges or moving parts. WARNING: Only use reduces the risk of electric shock.
7. Failure to follow all warnings and instructions... of their device and/or doctor for advice before operating this power tool. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Blows per minute Overall length Rated voltage Net weight
XKH01 0 - 3,200 /min 368...
XKH01 Instruction Manual - Page 3
...Follow all times. Service
1. Use personal protective equipment. Carrying power tools with specifically designated battery packs. ...replacement parts. Any power tool that is suitable for safe handling and control of battery pack may be repaired.
3. A charger that cannot be controlled with these are provided for your power tool serviced by the manufacturer or authorized service...
XKH01 Instruction Manual - Page 4
...to follow the safety rules stated in this instruction manual may be toxic. Do not short the battery...rinse them out with both hands.
10. Installing the batteries to water or rain. Wear ... the battery cartridge even if it from moving parts.
11. For preparation of your skin.
14... cause hearing loss.
2. Do not use ) replace strict adherence to disposal of overheating, possible burns and...
XKH01 Instruction Manual - Page 5
...will also void the Makita warranty for a few seconds.
Charge the battery cartridge before installing or removing of the battery cartridge. Never recharge a fully charged battery cartridge. Charge...do not use genuine Makita batteries. Indicator lamps 2. SAVE THESE INSTRUCTIONS. Overcharging shortens the battery service life.
3. FUNCTIONAL DESCRIPTION
To remove the battery cartridge, slide...
XKH01 Instruction Manual - Page 6
...of the following conditions:
Overload protection
When the battery is increased by turning the speed adjusting dial to a given number setting from A ( ) side. B
A
► 1 . B
A
1 2
► 1 . Tool ...released.
Trigger-lock button 2. Switch trigger
Speed adjusting dial
1
WARNING: Before installing the battery cartridge into the tool, always check to see that caused the ...
XKH01 Instruction Manual - Page 7
... action and longer service life.
► 1 . Shank end 2. Turn the bit and push it engages. Bit 2.
NOTE: Use a dry cloth to wipe the dirt off and the battery cartridge is removed before installing the bit.
2... function provides the constant rotation speed regardless of the lamp.
After installing the bit, always make sure that the tool is securely held in place by trying ...
XKH01 Instruction Manual - Page 8
...with the hook only. CAUTION: Never hook the tool at 12 different angles. Hook
Removing or installing the hook
To remove the hook, loosen the screws and remove the washers and hook. Washer
Connecting... hook, simply lift up hook until it snaps into the closed position.
1 ► 1 . CAUTION: Install or remove the hook on the tool housing, and then secure the hook with the screws. Be sure to...
XKH01 Instruction Manual - Page 9
... dropped, it falls. Loss of the lanyard outside the working "at height Read all safety warnings and instructions. In this tool type and rated for use .
5. Connecting lanyard (tether strap) to hook
Safety warnings specific for at each use if damaged or not functioning properly.
6. Always keep the tool tethered when working...
XKH01 Instruction Manual - Page 10
...and RELIABILITY, repairs, any other...available, refer to the warranty details set forth at below website for more details regarding these accessories, ask your local Makita Service Center. • Bull point •...Factory Service Centers, always using Makita replacement parts.
The use with your respective country. They may result. MAKITA LIMITED WARRANTY
Please refer to this manual. ...
XKH01 Parts Breakdown - Page 2
...345874-5 STEEL BALL GUIDE
010
450274-7 CHANGE RING
011
231985-1 RING SPRING 43
012
459752-4 SUPPORT RING
013
459748-5... PC. 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 2 PC. Model XKH01TJ/Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
286283-8 CAP 38
002
233966-1 RING SPRING 19
003
450275-5 CHUCK COVER
004
234039-3 COMPRESSION SPRING 42
...
XKH01 Parts Breakdown - Page 3
...-PA SWITCH LEVER COMPRESSION SPRING 5 CONTROLLER TERMINAL TAPPING SCREW 4X18 HOUSING SET RUBBER PIN 6 INC. 76 XKH01 SERIAL NO. LABEL PAN HEAD ... SQUARE NUT M5 HOOK ASS'Y XKH01 NAME PLATE CONNECTOR PLASTIC CASE (TYPE4) LATCH INNER TRAY XKH01TJ PLASTIC CASE LABEL XKH01TJ INDICATION LABEL BATTERY BL1850B SET (197283-2) BATTERY COVER DC18RC FAST CHARGER
1 PC. 4 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC...
XKH01TJ New Tool Flyers English - Page 1
...Accepts SDS-PLUS Power Type Cordless UPC Code 088381-891448 (XKU01TJ) UPC Code 088381-891455 (XKU01Z)
STANDARD EQUIPMENT
...models and accessories subject to stock on the job • 12 bit angle settings allow the bit to change without prior notice. Power Scraper (HK1810)
1
2
3
4
5
All specifications subject to be set at different positions for reduced operator fatigue
SPECIFICATIONS...
Makita XKH01Z Reviews
Do you have an experience with the Makita XKH01Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!