Makita XGD01PT Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XGD01PT manuals!
Problems with Makita XGD01PT?
Ask a Question
Free Makita XGD01PT manuals!
Problems with Makita XGD01PT?
Ask a Question
Popular Makita XGD01PT Manual Pages
XGD01 Instruction Manual - Page 2
... subject to change without notice.
• Specifications may differ from heat, oil, sharp edges or moving parts. Do not abuse the cord. Never use... SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all instructions listed below may cause injury and/or fire. ENGLISH (Original instructions)
SPECIFICATIONS
Model: No load speed
Drilling capacities
High Low
XGD01 0 - ...
XGD01 Instruction Manual - Page 3
...specifically designated battery packs. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of parts and any other small metal objects, that have the power tool repaired...together may damage the battery and increase the risk of the power tool in the instructions. Protective equipment such as dust mask, non-skid safety shoes, hard hat, ...
XGD01 Instruction Manual - Page 4
... may make sure that the safety of the auger bit must be performed by a qualified repair person using battery.
2. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using only identical replacement parts. If electrolyte gets into your skin.
13. Do not nail, cut, crush, throw, drop...
XGD01 Instruction Manual - Page 5
...Overcharging shortens the battery service life.
3. Let a... SETTING
CAUTION: Always be observed. Unless the tool supports ...PARTS DESCRIPTION
1
2
3
4
5
6
7
8
A
B
C
H
AB C
1 Main tool 3 Side handle 5 Bit adapter 7 Bolt
2 Front handle 4 Reaction receiver 6 Chuck key 8 Wrench
Specifications...Installing the batteries to the Dangerous Goods Legislation requirements. It may take ...
XGD01 Instruction Manual - Page 6
...lost.
Side handle 2. The removed bolt is in the figure from the tool. Installing the side handle
Remove the bolts shown in the center of the operator. The indicator... the tool. Indicating the remaining battery capacity
Only for battery cartridges with the indicator
32 1
3 ► 1 . Setting up for this tool if you want to use this tool as a cordless earth auger.
Bolt A 3.
XGD01 Instruction Manual - Page 7
... In this case, remove the battery from the actual capacity. Switch action
CAUTION: Before installing the battery cartridge into the tool, always check to see that the switch trigger actuates ...tool is operated in use and the ambient temperature, the indication may have the tool serviced at a Makita service center.
7 ENGLISH Main power switch
WARNING: Always turn the tool on the conditions ...
XGD01 Instruction Manual - Page 8
...the "high speed mode" for powerful operation.
1 1
► 1 .
NOTICE: Always set the reversing switch lever to change knob positioned halfway between the position 1 and the position ... NOTICE: Use the tool at low speed (position 1). CAUTION: When not operating the tool, always set the speed change
► 1 .
NOTICE: Use the speed change function
This tool has "high ...
XGD01 Instruction Manual - Page 9
...Installing or removing battery cartridge
3 2 1
► 1 . Speed change knob so that the pointer points to you or someone around you can be seen.
When this happens, the drill bit will actuate when a certain torque level is reached at the low speed setting...limiter
The torque limiter will stop turning. CAUTION: Always install the battery cartridge fully until it locks in the ...
XGD01 Instruction Manual - Page 10
... important that the tool is switched off and the battery cartridge is removed before carrying out any damages. To install the bit adapter, place the bit adapter in the openings or moving parts.
10 ENGLISH Be sure to the storage cavity on the tool. Align the hole on the bit adapter with...
XGD01 Instruction Manual - Page 11
...: If the tool is removed before proceeding with both hands. Dig the hole by setting the reversing switch to reverse rotation in small steps. When rotating the auger bit in...Keep proper positioning by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
11 ENGLISH
To maintain product SAFETY and RELIABILITY, repairs, any other things that may not be sure...
XGD01 Instruction Manual - Page 12
... sheet is not available, refer to the warranty details set forth at below website for more details regarding these accessories, ask your local Makita Service Center. • Auger bits • Bit adapter ....
They may be included in this product. MAKITA LIMITED WARRANTY
Please refer to this manual. The use of America: www.makitatools.com Canada: www.makita.ca Other countries: www...
XGD01Z Parts Breakdown - Page 3
... COMPLETE
1
1
37 226175-9
SPUR GEAR 14
1
1
38 310876-0
CHANGE RING
1
1
39 253215-0
FLAT WASHER 8
1
1
40 347366-0
CHANGE GUIDE
1
rev 0_08/19/20
3
Notes INC. 7
INC. 12,26 INC. 29 No. XGD01 Tech Bulletin
Part No. FLAT HEAD SCREW M6X22
1
1
19 140A22-5
GEAR HOUSING COMPLETE
1
1
20 265695-8
H. 1 XGD01
Motor and Gear Housing
Products...
XGD01Z Parts Breakdown - Page 4
... top not indented. No. XGD01 Tech Bulletin
Part No.
BOLT M5X30 WITH WRM
4
1
63 140A19-4
SWITCH CIRCUIT COMPLETE
1
1
64 183R46-0
HANDLE SET
1
1
65 620839-1
LED CIRCUIT
1
... CHANGE LEVER
1
1
68 650710-5
SWITCH C3JW-4B
1
1
69 620838-3
CONTROLLER
1
1
70 183R46-0
HANDLE SET
1
1
71 644809-6
TERMINAL
2
1
74 212193-3
NEEDLE CAGE 5810
3
1
75 267010-2
FLAT WASHER 5
1...
XGD01Z Parts Breakdown - Page 6
.... Section Fig.
XGD01 Tech Bulletin
Part No. 2 XGD01
Pipe Grip Assembly
Products with multiple versions are listed in subsiding order with the newest version on top not indented. WRENCH 5
1
A06 327684-2
ADAPTER A
1
A09 327687-6
ADAPTER D
1
A10B ***DC18RD
DC18RD TWO PORT FAST CHARGER
1
A11B BL1850B
BATTERY BL1850B SET
2
A12B 450128-8
BATTERY COVER
2
Notes...
XGD01Z New Tool Flyers English - Page 1
...UPC Code ...• Chuck Key (763251-3)
1
2
3
4
5
All specifications subject to stock on hand. Patent and Trademark Office. All models and accessories subject to change without battery 15.1 lbs. Earth Auger..., construction and soil sampling
• Ideal for post-hole digging, fence installation, large planting jobs and construction projects
• 2 speed options (Low:...
Makita XGD01PT Reviews
We have not received any reviews for Makita yet.