Makita XGC01M1C Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XGC01M1C manuals!
Problems with Makita XGC01M1C?
Ask a Question
Free Makita XGC01M1C manuals!
Problems with Makita XGC01M1C?
Ask a Question
Popular Makita XGC01M1C Manual Pages
Makita XGC01Z Instruction Manual - Page 2
...surfaces such as dust mask, non-skid safety shoes, hard hat, or
2
Personal safety 10. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XGC01
Max feed force
5,000 N (1,100 lbs)
Feed speed
0 - 28 mm/s (0 - 66 inch...Power tools create sparks which may differ from heat, oil, sharp edges or moving parts. Distractions can cause you are doing and use a power tool while you to ...
Makita XGC01Z Instruction Manual - Page 3
... better and safer at all times. Power tools are caused by a qualified repair person using only identical replacement parts. Maintain power tools. A charger that is in use, keep it was designed. 18. Hold the tool firmly. 4. Read and follow the manufacture's instructions on caulking material or adhesive material before turning the power tool on...
Makita XGC01Z Instruction Manual - Page 4
... product
(gained from repeated use) replace strict adherence
to water or rain.... 5. Overcharging shortens the battery service life. 3. Before using battery cartridge, read all instructions and cautionary markings on (1) battery...volts
･ direct current
IMPORTANT SAFETY INSTRUCTIONS
ENC007-8
FOR BATTERY CARTRIDGE
1. Charge ...THESE INSTRUCTIONS.
MISUSE or
failure to follow ...
Makita XGC01Z Instruction Manual - Page 5
...the battery cartridge. • Hold the tool and the battery cartridge firmly when
installing or removing battery cartridge. This system automatically cuts off the tool before pulling the...Do not install the battery cartridge forcibly.
Insert it all the way until the
red indicator cannot be sure that case set the speed adjusting dial higher.
5 CAUTION: • Always install the battery...
Makita XGC01Z Instruction Manual - Page 6
... Lamp
013557
The warning lamp flickers in ))
013610
Attach the holder joint firmly along the tool, set the plate, and fix them with screws tightly. NOTE: Check what causes the overload when the lamp...the speed adjusting dial lower, or increase the diameter of the caulking material and prevents dripping.
Installing holder joint For short holder (300ml(18.3cu.in)) and long holder (600ml(36.6cu....
Makita XGC01Z Instruction Manual - Page 7
... piston and tighten it with holder type. • Always keep the rod and piston clean. Installing rod and piston For short holder (300ml(18.3cu.in))
013611
For big holder (800ml(48...types of rods. Improper piston may damage the tool.
7 To remove the holder joint, follow the installation procedure in )). NOTE: • There are three types of holders (optional
accessory), short holder ...
Makita XGC01Z Instruction Manual - Page 8
...then take out the cartridge. Do not use damaged cartridge, otherwise the tool may be damaged. Installing film type pack NOTICE: • Make sure the piston B is tightened firmly. Push the ... with the holder type. NOTICE: • Always check the cartridge for puncture or
damage before installing. Holder cap 1
013571
Insert the cartridge into the short holder (300ml(18.3cu.in))
1. ...
Makita XGC01Z Instruction Manual - Page 9
... Do not touch the rod during operation. Replace the caulking material when it
becomes soft....set to 1, and pull the switch trigger for the following items: • Nozzle tip is filled in the nozzle. Rubber ring 2. Cut off and the
battery cartridge is not dispensed, check the following troubleshooting related to move. NOTE: If the caulking material is removed before installing...
Makita XGC01Z Instruction Manual - Page 10
...any trouble develop during this manual. The use of the tool. MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is warranted to you. This Warranty gives you specific ...be included in )) set • Plate (If you have been made to you may be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. EN0006-1
10
Remained...
XGC01Z XGC01ZB XGC01ZC Parts Breakdown - Page 2
Model XGC01Z/XGC01ZB/XGC01ZC Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
142071-2
001
142072-0
001
143221-2
002
266827-0...HOLDER JOINT C RACK 42 COMPLETE RACK 64 COMPLETE RACK 53 COMPLETE XGC01 NAME PLATE TAPPING SCREW 3X16 HOUSING SET RUBBER PIN 6 INC. 24 LENS SUB CONTROLLER SYNCHRO BELT 4-176 SPUR GEAR 9A COMPLETE LENS GEAR ASSEMBLY...
Makita XGC01ZC/XGC01M1C New Tool Flyer English - Page 1
...oz. UPC Code XGC01M1C 088381-697705
n Ergonomic design at makitatools.com, or call 1-800-4MAKITA. 18V LXT® Lithium-Ion Cordless 29 oz.
Conversion Kit (196352-6)
All specifications subject to...
SPECIFICATIONS
n Makita-built motor delivers 1,100 lbs. cartridges
Speed settings 5
n Drip-reduction feature automatically relieves pressure on hand. of dispensing force
POWER
Makita-...
Makita XGC01M1C Reviews
We have not received any reviews for Makita yet.