Makita XFD14Z Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XFD14Z manuals!
Problems with Makita XFD14Z?
Ask a Question
Free Makita XFD14Z manuals!
Problems with Makita XFD14Z?
Ask a Question
Popular Makita XFD14Z Manual Pages
Instruction Manual - Page 2
...an extension cord suitable for outdoor use the cord for future reference. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Drilling capacities
Fastening capacities
No load speed (RPM)
Overall length Rated voltage Net weight..., are subject to change without notice.
• Specifications may differ from heat, oil, sharp edges or moving parts. Use of a cord suitable for outdoor use any...
Instruction Manual - Page 3
...parts.
7. Do not overreach. Do not let familiarity gained from those intended could result in a hazardous situation.
8.
Power tools are tired or under the influence of dust extraction and collection facilities, ensure these instructions...tool that may be repaired.
3. Many accidents ...contact accidentally occurs, flush with specifically designated battery packs. Keep your ...
Instruction Manual - Page 4
...service damaged battery packs. Symbols
The followings show the symbols used for lubricating and changing accessories.
4. Hold the power tool by a qualified repair person using only identical replacement parts. Do not touch the drill bit or the workpiece immediately after operation; Safety instructions... with the bit tip in this instruction manual may reach or exceed 50 °...
Instruction Manual - Page 5
... dust, or soil stuck into place. SAVE THESE INSTRUCTIONS. Use of the battery cartridge. Charge the battery cartridge...the battery cartridge firmly when installing or removing battery cartridge.
Unless the tool supports the use near high-... is required.
Overcharging shortens the battery service life.
3. CAUTION: Always install the battery cartridge fully until it cannot...
Instruction Manual - Page 6
...works when the remaining battery capacity gets low. Switch action
CAUTION: Before installing the battery cartridge into the tool, always check to become overloaded. Indicator ...turn the tool on the conditions of use and the ambient temperature, the indication may have the tool serviced at a Makita service center. Then turn the tool off the power to 25%
Charge the battery. Lighting up for ...
Instruction Manual - Page 7
.... Be careful not to the correct position. CAUTION: When not operating the tool, always set the speed change lever while the tool is rotating.
7 ENGLISH Be sure that you operate... mode (rotation only)
1 - 21
Screwdriving mode (rotation with the adjusting ring. NOTICE: Always set to display "1" and restart the operation.
Arrow
This tool has two action modes.
Push the speed...
Instruction Manual - Page 8
Arrow
The fastening torque can be fixed at 21.
Close 3.
Installing side grip (auxiliary handle)
3
Installing or removing driver bit/ drill bit
1 3
2
1 2 4
► 1 . Groove 4. Open
Turn the sleeve counterclockwise to tighten the chuck. Install the side grip so that the tool is switched off and the battery cartridge is required for a particular application. The ...
Instruction Manual - Page 9
... the hanging/mounting parts for temporarily hanging the tool. Using for your belt using the driver bit, keep it out.
Groove 2. To install the hook, insert it into the protrusion at the tool foot on either side of the driver bit in the driver bit holders.
Driver bits 45 mm-long (1-3/4") can be installed on the tool...
Instruction Manual - Page 10
... performance and shorten the service life of the tool.... ask your local Makita Service Center. • Drill bits • Driver bits • Hook ...Service Centers, always using Makita replacement parts.
10 ENGLISH CAUTION: Always secure workpieces in order to back out. To maintain product SAFETY and RELIABILITY, repairs...workpiece. The guide screw makes drilling easier by setting the reversing ...
XFD14 Parts Breakdown - Page 2
... C10 140U91-6 POLE COMPLETE
A01 C20 140X19-2 ARM R COMPLETE
A01 C30 266886-4 HEX. Model XFD14T/Z Parts List
A = Standard Equipment
〇= Circuit Diagram
Item#
Part#
Description
001
811B50-0 XFD14 NAME PLATE
002
266130-9 TAPPING SCREW BIND PT 3X16
003
191M80-6 HOUSING SET
003 C10 263005-3 RUBBER PIN 6
003 C20 252126-6 HEX. LABEL
019
620549-0 LED...
New Tool Flyers English - Page 1
...XPS® 60 Pc. UPC Code 088381-739696
STANDARD EQUIPMENT
•... previous model
VERSATILITY
...Set (E-01650) 3. Impact Bit Set (E-01666) 4. 18V LXT® Lithium-Ion 5.0Ah Battery, 2/pk (BL1850B-2) 5. 18V LXT® Lithium-Ion Rapid Optimum Charger (DC18RC)
1
2
3
4
5
All specifications subject to change without prior notice. 18V LXT® LITHIUM-ION BRUSHLESS CORDLESS 1/2" DRIVER...
Makita XFD14Z Reviews
Do you have an experience with the Makita XFD14Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!