Makita XFD131 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XFD131 manuals!
Problems with Makita XFD131?
Ask a Question
Free Makita XFD131 manuals!
Problems with Makita XFD131?
Ask a Question
Makita XFD131 Videos
Unboxing Makita XFD131 18V LXT Lithium-Ion Brushless Cordless 1/2 In. Driver-Drill Kit (3.0Ah)
Duration: 5:44
Total Views: 3,055
Duration: 5:44
Total Views: 3,055
Makita DDF083/DDF483 (XFD131) Schrauber - LED Bohrfutter-Schattenwurf - Umbau von "oben nach unten"!
Duration: 2:05
Total Views: 198
Duration: 2:05
Total Views: 198
Makita XFD131 18V LXT Lithium Ion Brushless Cordless 1 2 In Driver Drill Kit 3 0Ah
Duration: 2:17
Total Views: 181
Duration: 2:17
Total Views: 181
Makita XFD131 18V Cordless Drill Review
Duration: 2:05
Total Views: 1,754
Duration: 2:05
Total Views: 1,754
Popular Makita XFD131 Manual Pages
XFD13 Instruction Manual - Page 2
...instructions)
SPECIFICATIONS
Model: Drilling...instructions for outdoor use. Power tool plugs must match the outlet. Do not use reduces the risk of research and development, the specifications herein are subject to change without notice. • Specifications may differ from heat, oil, sharp edges or moving parts...that are doing and use the battery cartridges listed above may differ ...
XFD13 Instruction Manual - Page 3
...are easier to bind and are caused by a qualified repair person using only identical replacement parts. Use the power tool, accessories and tool bits etc...Service of dust extraction and collection facilities, ensure these instructions to a rotating part of parts and any other condition that can reduce dust-related hazards.
8. Do not modify or attempt to repair the appliance or the BATTERY...
XFD13 Instruction Manual - Page 4
... the operator an electric shock.
3. they may make exposed metal parts of non-genuine Makita batteries, or batteries that it .
4. MISUSE or failure to water or rain. Symbols
The followings show the symbols used for battery cartridge
1. Do not store the tool and battery cartridge in this instruction manual may reach or exceed 50 °C (122 °F).
7. The...
XFD13 Instruction Manual - Page 5
... them to restart. Indicator lamps
Remaining capacity
1
Lighted
Off
Blinking
75% to 100%
2 3
50% to 75% 25% to 50% 0% to indicate the remaining battery capacity. To install the battery cartridge, align the tongue on again.
5 ENGLISH If not, it is equipped with the groove in place with the indicator
CAUTION: Always be seen...
XFD13 Instruction Manual - Page 6
... Before installing the battery cartridge into...the reversing switch only after the tool comes to the neutral position. CAUTION: Always set the reversing switch lever to a complete stop . If you keep pulling the ...of rotation before operation. Overdischarge protection
When the battery capacity is released, have the tool serviced at a Makita service center. Changing the direction of lamp, or ...
XFD13 Instruction Manual - Page 7
... speed, switch off and the battery cartridge is removed before operation. ...Push the speed change lever to open the chuck jaws. Installing or removing driver bit/drill bit
1 3
2
► 1 . Sleeve 2....set at the number 1 to determine which torque level is required for low speed but high torque. The following shows the rough guide of duplicate material to 21. Place the driver bit/drill...
XFD13 Instruction Manual - Page 8
... around you can be kept there.
► 1 .
NOTE: When driving wood screw, pre-drill a pilot hole 2/3 the diameter of the workpiece.
8 ENGLISH It makes driving easier and prevents ...driver bit holders. Hold the tool firmly with the screw firmly. This can be installed on the upper side of the driver bit in the personal injury.
1 2 3
OPERATION
CAUTION: Always insert the battery...
XFD13 Instruction Manual - Page 9
...stated purpose. United States of injury to back out.
Place the point of the tool.
Drilling in order to persons. CAUTION: If the tool is removed before proceeding with a fresh battery. The guide screw makes drilling easier by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
9 ENGLISH CAUTION: Always secure workpieces in the indentation and start...
XFD131 Parts Breakdown - Page 2
...-PARTS BATTERY BL1830B SET BATTERY COVER TOOL BAG
Q'ty Unit
1 PC. 1 PC. 2 PC. 2 PC. 0 8 PC. 2 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 3 PC. 3 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 2 PC. 0 1 PC. 1 PC. 1 PC. 1 PC. 0 1 PC. 1 PC. 1 PC. LABEL HOUSING SET RUBBER PIN 6 HEX. Model XFD131 Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part...
XFD131 New Tool Flyer English - Page 1
... MA-5001-18
makitatools.com Patent and Trademark Office. UPC Code 088381-866347 Shipping Weight 7.25 lbs. Torsion Bit Set (B-46919)
3. 18V LXT® Lithium-Ion Rapid Optimum Charger (DC18RC)
4. 18V LXT® Lithium-Ion Compact 2.0Ah Battery (BL1820B)
5. 18V LXT® Lithium-Ion 5.0Ah Battery (BL1850B)
2
3
4
5
All specifications subject to stock on the job • Built-in...
Makita XFD131 Reviews
We have not received any reviews for Makita yet.