Makita XEC01Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XEC01Z manuals!
Problems with Makita XEC01Z?
Ask a Question
Free Makita XEC01Z manuals!
Problems with Makita XEC01Z?
Ask a Question
Popular Makita XEC01Z Manual Pages
XEC01PT1 Instruction Manual - Page 2
... cartridges and chargers listed above may result in the presence of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from heat, oil, sharp edges or moving parts. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Diamond wheel diameter Max. Power tool plugs must match the outlet. permitted pressure of feed...
XEC01PT1 Instruction Manual - Page 3
...service providers.
3. Recharge only with specifically designated battery packs. Do not use of appropriate safety protective equipment by the tool operators and by the manufacturer. Follow all times. Follow instruction... from injury when using only identical replacement parts. If devices are connected and properly used for one terminal to repair the appliance or the battery pack ...
XEC01PT1 Instruction Manual - Page 4
... cause electrical hazards.
16. Proper wheel flanges support the wheel thus reducing the possibility of snagging..... The wheel may cause them to make exposed metal parts of the binding. Abrasive wheels may also break under these...-off wheel. Always use , inspect the wheels for damage or install an undamaged wheel. Incorrectly sized accessories cannot be capable of correct diameter...
XEC01PT1 Instruction Manual - Page 5
... tool. Do not use ) replace strict adherence to cut before cutting...Support panels or any con- The protruding wheel may result in a con- ductive material. (2) Avoid storing battery cartridge in loss of your local regulations relating to remove the wheel from the tool and dispose of 10 mm or less, only with clear water and seek medical attention right away. In this instruction manual...
XEC01PT1 Instruction Manual - Page 6
.... 12. SAVE THESE INSTRUCTIONS. Use of non-genuine Makita..., personal injury and damage. Installing the batteries to non-compliant .... Charge the battery cartridge with the products specified by Makita. PARTS DESCRIPTION
2 1
3
4
5
8
7
6
10 11 ... trigger 16 Cover (for V-belt) -- Overcharging shortens the battery service life.
3. Let a hot battery cartridge cool down before completely ...
XEC01PT1 Instruction Manual - Page 8
... situation, reduce the load on the tool. Overload indicator
Switch action
WARNING: Before installing the battery cartridge into the tool, always check to see that caused the tool to...stop the application that the switch trigger actuates properly and returns to a Makita service center for proper repairs BEFORE further usage.
8 ENGLISH Battery indicator 2.
Overload alert
If the tool is...
XEC01PT1 Instruction Manual - Page 11
... full capacity.
Then, the tool can work to lock the cover for the operation. Hold the tool firmly. Water inlet 3.
Cock 11 ENGLISH 4. Coupling sleeve 2.
Part to the water supply and turn the cock in the figure.
1
3 2
1
► 1 . Connect the tool to hold
Move the tool over the workpiece surface, keeping...
XEC01PT1 Instruction Manual - Page 12
...like. Wheel guard 2. Discoloration, deformation or cracks may cause electric shock. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be sure that the tool is switched off the lens of the lamp
... Inhalation vent 2. Clean the tool body by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
1 2
► 1 .
XEC01PT1 Instruction Manual - Page 13
...come off as you turn the bolt.
► 1 . All the rails on the pulley must support the guides on the V-belt
► 1 . Box wrench
NOTICE: Never turn the bolt on the pulleys... (large) and then turn the box wrench counterclockwise. If there is a rail which does not support the guide, the V-belt is not properly installed.
1
2
3 1
2 ► 1 . Rail on the pulley (large) and result ...
XEC01PT1 Instruction Manual - Page 14
... does not work correctly. Recharge the battery. Install the battery cartridge as shown in the figure before
attaching the cover.
1 2 3
► 1 .
NOTICE: Make sure that is not effective, replace the battery cartridge. Hex socket bolt
TROUBLESHOOTING
Before asking for repair. If you find a problem that the tube for repair.
14 ENGLISH State of tool to allow...
XEC01PT1 Instruction Manual - Page 15
... not available, refer to the warranty details set forth at below website for your local authorized service center for repair. Remedy Install the wheel as standard accessories. Tighten the bolt to replace the wheel. Ask your respective country.
They may be included in the tool package as instructed in this manual.
State of injury to persons. Probable...
XEC01Z Parts Breakdown - Page 3
...
1 33 266326-2
TAPPING SCREW 4X18
3
1 34 412344-0
BATTERY LOWER COVER L
1
1 35 347659-5
GUIDE PLATE
1
rev 0_05-19-20
3
Notes INC. 11-15 INC. 31,32 Description
1 1 266976-3
...
1
1 13 256947-8
SHOULDER PIN 7
1
1 14 961012-7
STOP RING E-6
1
1 15 265880-3
H.S.SET SCREW(CONE POINT)M5X8
1
1 16 136250-2
CUTTING DEVICE ASSY
1
1 17 922333-2
HEX.SOCKET HD BOLT M6X20...Part No.
XEC01Z Parts Breakdown - Page 6
... 412342-4
SWITCH LEVER
1
2 77 651083-9
SWITCH C3XA-1PSPM
1
rev 0_05-19-20
6
Notes
INC. 53,55,56 INC. 61 INC. 58 No.
XEC01 Tech Bulletin
Part No. Section Fig. 2 XEC01
Terminal Housing Set
Products with multiple versions are listed in subsiding order with the newest version on top not indented.
XEC01Z Parts Breakdown - Page 7
BOLT M8X27
1
2 83 127491-1
HOSE ASSEMBLY
1
Notes
rev 0_05-19-20
7 XEC01 Tech Bulletin
Part No. Description
2 79 232267-4
LEAF SPRING
1
2 80 266326-2
TAPPING SCREW 4X18
1
2 82 265B45-9
HEX. No.
2 XEC01
Terminal Housing Set
Products with multiple versions are listed in subsiding order with the newest version on top not indented.
Section Fig.
XEC01Z New Tool Flyers English - Page 1
...-0620 MA-8818-20
4
5
makitatools.com All models and accessories subject to change without prior notice. Patent...run cooler and more efficiently for longer life; UPC Code 088381-731461 (XEC01PT1) UPC Code 088381-899390 (XEC01Z)
STANDARD EQUIPMENT
XEC01PT1 • ...Filter Dust Extractor/Vacuum, AWS™ Capable (VC4210L)
All specifications subject to stock on /off if rotation of the wheel...
Makita XEC01Z Reviews
We have not received any reviews for Makita yet.