Makita LW1400X2 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita LW1400X2 manuals!
Problems with Makita LW1400X2?
Ask a Question
Free Makita LW1400X2 manuals!
Problems with Makita LW1400X2?
Ask a Question
Popular Makita LW1400X2 Manual Pages
LW1400 LW1401 Instruction Manual - Page 2
...be properly repaired or replaced.
20. check for alignment of moving parts, binding of moving parts. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
LW1400
LW1401...using your own safety, read instruction manual before plugging in presence of the tool, a guard or other part that is in damp or ...servicing; Before further use tool in .
17.
WEAR PROPER APPAREL. SECURE WORK.
LW1400 LW1401 Instruction Manual - Page 3
...replacement parts.
23. Do not touch the workpiece immediately after operation;
NEVER LEAVE TOOL RUNNING UNATTENDED. When servicing... that could indicate poor installation or a poorly balanced ...12
Not Recommended
Specific safety rules
DO...instruction manual may cause serious personal injury.
3 ENGLISH They can result in this tool.
6. Remove material or debris from rotating parts...
LW1400 LW1401 Instruction Manual - Page 4
...
CAUTION: Always be bolted with two bolts to see that there is switched off and unplugged before starting the operation. INSTALLATION
WARNING: This tool produces spark when cutting a workpiece. Do not install this tool in the place in the tool's base. Bolt holes 2. Hook 2. For LW1400 To unlock, depress the tool head...
LW1400 LW1401 Instruction Manual - Page 5
...following interval settings of repair may result in personal injury. For LW1400 Loosen the screw on the guide plate. Move the guide plate to change the spacing or interval. Guide plate 2. ... button. Move the guide plate to stop. Guide plate For LW1401 Remove the two hex bolts using a socket wrench. Move the guide plate to a Makita service center for proper repairs BEFORE further usage....
LW1400 LW1401 Instruction Manual - Page 6
... off wheel is installed, set angle while securing the hex bolts.
► 1 . Guide plate 2.
Turn the guide plate to position ... guide plate and the cutoff wheel with the hex bolts.
CAUTION: Always lower the safety guard after replacing ...ruler. Guide plate 2. 1
Stopper plate
2
For LW1401 only (country specific)
B
1 A
► 1 . CAUTION: Be sure to move the set the ...
LW1400 LW1401 Instruction Manual - Page 7
... 6. When removing the cut -off wheel to the ring and return the safety guard. Toolless clamp
To install the cut -off wheel, do not remove the inner flange as well as , possible damage to the tool... fully elevated position. 1
3
2
2
1
4
5
6
► 1 .
Ring 3. Hex bolt
To install the wheel, follow the removal procedures in reverse. Do not force the cut by the amount of cut .
LW1400 LW1401 Instruction Manual - Page 8
... cause a dangerous breakage of the workpiece. Use non-flammable material for a spacer block.
Guide plate 2. Thread holder 3. Vise plate
When the cut -off wheel does not contact the... tool head is slightly narrower than the workpiece as shown in and out quickly.
This will be supported by putting a spacer block which is depressed.
1
2
3
4
► 1 . Workpiece diameter...
LW1400 LW1401 Instruction Manual - Page 9
... Authorized Service Centers.
Replacing carbon ...Replace them when they wear down the tool head and lock it. Only use gasoline, benzine, thinner, alcohol or the like.
Supporting block
Carrying tool
Fold down to persons. Keep the carbon brushes clean and free to remove the brush holder caps. 2.
If you need any trouble develop during this manual...repair (or at the same time. ...
LW1400 LW1401 Instruction Manual - Page 10
... been made or attempted by others: • repairs are required because of incidental or consequential damages, so the above limitation may ...FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may not apply to you . IN NO EVENT SHALL ...
Makita LW1400 Parts Breakdown - Page 2
Model LW1400 Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
213858...O-RING 65 PAN HEAD SCREW M5X20 FLANGE 90 TOOLLESSBOLT ASSEMBLY PLUG PLUG SAFETY GUIDE + FLAT HEAD SCREW M6 O RING 14 RING 17 FLANGE 90 RING ... SPINDLE BALL BEARING 6000ZZ HANDLE SET INC. 30 SWITCH TGC31B SWITCH LEVER SWITCH LOCK COMPRESSION SPRING 4 HANDLE SET INC. 23 SWITCH BUTTON TAPPING...
Makita LW1400 Parts Breakdown - Page 3
... 5-20 HANDLE 120 VISE SCREW H.S.SET SCREW(FLAT POINT)M6X16 VISE NUT PLATE SCREW GUIDE SPRING PIN 5-36 SPRING PIN 4-16 PAN HEAD SCREW M8X30 COLLAR BOLT M10X20 KNOB 40 GUIDE PLATE HEX.NUT M10-17 SPRING... S-16 FLAT WASHER 8 VISE PLATE WAVE WASHER 6 INSULATION WASHER PAN HEAD SCREW M4X6 SPARK COVER H.S.SET SCREW(FLAT POINT)M5X6 LEVER 125 FLAT WASHER 10 SLEEVE 11 FLAT WASHER 10 THRUST NEEDLE CAGE 1024 ...
Makita LW1400X2 Reviews
We have not received any reviews for Makita yet.